TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

856 hydraulics

Welcome Guest, Log in or Register

Author

Robhkent

08-17-2005 18:48:13

Report to Moderator

OK, need a little help here.

I have an 856 with a single hydraulic valve. I have a new (to me) Koyker K5 loader. I have a new joystick valve to hook up to run the loader, and I do not want to use the existing valve to feed the joystick. I have pulled off the seat and I see a plug to the left of the single valve. I think this plug goes into the valve for the 2 point. There is also a plug on the side of the same valve. Just to the front of the back bolt hole in the picture. Can I plumb my joystick valve in here? If not here, is there another way besides using the single valve to feed the joystick??

Thanks

Rob

[Log in to Reply] [No Email]

Allan in NE

08-17-2005 19:25:24

Report to Moderator

Re: 856 hydraulics in reply to Robhkent, 08-17-2005 18:48:13

Heck,

I'd simple this whole process up and just put on a PTO pump and a tank. That leaves your tractor's hydraulics free.

Allan

[Log in to Reply] [No Email]

Robhkent

08-17-2005 19:34:18

Report to Moderator

Re: 856 hydraulics in reply to Allan in NE, 08-17-2005 19:25:24

I thought of that Allan, but I don't want to use that poor old 540 pump off an equally old cyclo air 400. Besides, that kind of gets away from the Quick attach nature of the loader, and if I use the tractor for other things next spring like planting 24 acres of beans, I need the pto for the aforementioned Cyclo air 400 and I might need more than one outlet for things like a 470 disk pulling a sprayer.....

Rob

[Log in to Reply] [No Email]

Robhkent

08-17-2005 18:50:03

Report to Moderator

Re: 856 hydraulics in reply to Robhkent, 08-17-2005 18:48:13

OK, trying the pic again.

third party image

[Log in to Reply] [No Email]

Nat

08-17-2005 19:10:47

Report to Moderator

Re: 856 hydraulics in reply to Robhkent, 08-17-2005 18:50:03

As I understand it, you would need the "power beyond" end plate that covers the valve stack on the right in that picture (left as you sit on the seat). Problem is, you also need a different valve because that one doesn"t have the removeable end plate like the early "06s did.

I"m afraid you can"t plumb it without going through the existing valve.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy