Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

M steering

Welcome Guest, Log in or Register
Author 
makin'hay

06-25-2005 15:57:15




Report to Moderator

does anyone know why my front wheels [narrow] on my M wobble when going down the road in 5th ? i have an aftermarket power steering unit installed. the wheel bearings seem like they are fine. any ideas ? thanks




[Log in to Reply]   [No Email]
makin'hay

06-27-2005 17:33:15




Report to Moderator
 Re: M steering in reply to makin'hay, 06-25-2005 15:57:15  

glenn, thanks for the info. there was alot of play in the stops by the post. i also turned the gear around. next stop,...new bushings. thanks again



[Log in to Reply]  [No Email]
RustyFarmall

06-26-2005 07:34:16




Report to Moderator
 Re: M steering in reply to makin'hay, 06-25-2005 15:57:15  
The biggest reason for this is worn out bushings in the bolster. The shaft is no doubt worn also. A good machine shop can build up the shaft and the bushings should be available from your local dealer.



[Log in to Reply]  [No Email]
makin'hay

06-26-2005 13:17:42




Report to Moderator
 Re: M steering in reply to RustyFarmall, 06-26-2005 07:34:16  
thanks..... i jacked up the front end and sure enough, it is very loose in the bolster. i will check rims also. thanks again.



[Log in to Reply]  [No Email]
makin'hay

06-26-2005 13:17:41




Report to Moderator
 Re: M steering in reply to RustyFarmall, 06-26-2005 07:34:16  
thanks..... i jacked up the front end and sure enough, it is very loose in the bolster. i will check rims also. thanks again.



[Log in to Reply]  [No Email]
Glen E.

06-25-2005 18:20:23




Report to Moderator
 Re: M steering in reply to makin'hay, 06-25-2005 15:57:15  
Three things I have found on mine:
1. The rims are bent. Bent rims wobble like crazy.
2. Where the steering shaft goes through the post (under the throttle lever) there are two stops that must be not have any slack between them and the post.
3. The gear in top of the steering sector. If you are lucky enough to have a full gear, rather than a half gear, take it out and turn it around to the un-worn part.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy