TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Hopeing to tape experience of others

Welcome Guest, Log in or Register

Author

Hayfarmer

06-09-2005 21:20:19

Report to Moderator

Put electronic ignition on my SMTA. Had stock coil on before so got coil also. The old coil clamp isn't big enough for new coil. Can find a chrome clamp for not too much but somehow not sure it looks right on the rusty red tractor. Also thought of putting coil up under hood, pointed down to avoid mositure. How have others handled this?

[Log in to Reply] [No Email]

Theman

06-10-2005 10:46:32

Report to Moderator

Re: Hopeing to tape experience of others in reply to Hayfarmer, 06-09-2005 21:20:19

I had the same problem putting a new coil on my H. Had to make a temporary copy out of sheet metal that didn't look too shabby. It went back over the distributor so I could use the same coil wire and not have to re-route the primary wires too. Then I found out about the Pertronix P/N 10001 clamp. The cost was very reasonable. It is zinc plated but will get a coat of black paint before installation.

The hot coil, 40 thou. gap, and Ignitor module made a vast difference in cold starting after sitting for weeks at a time.

[Log in to Reply] [No Email]

Theman

06-10-2005 08:48:45

Report to Moderator

Re: Hopeing to tape experience of others in reply to Hayfarmer, 06-09-2005 21:20:19

The hot coil, 40 thou. gap, and Ignitor module made a vast difference in cold starting after sitting for weeks at a time.

[Log in to Reply] [No Email]

ChadS

06-10-2005 07:29:08

Report to Moderator

Re: Hopeing to tape experience of others in reply to Hayfarmer, 06-09-2005 21:20:19

Mount it next to the air cleaner up under the hood, use a long coil wire, bout anyplace else, and your looking at putting it too close to heat from the engine. Did you get the 55,000 volt coil? Chad

[Log in to Reply] [No Email]

Andy Martin

06-10-2005 05:01:11

Report to Moderator

Re: Hopeing to tape experience of others in reply to Hayfarmer, 06-09-2005 21:20:19

I have tied them on with electrical wire.

If you don't like the chrome, you can paint it.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy