Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Farmall & IHC Tractors Discussion Forum
:

560 Power Steering

Welcome Guest, Log in or Register
Author 
red paint gotta

02-13-2005 18:51:38




Report to Moderator

have any of you guys ever worked on power steering on a 560 farmall? I went by the book and still have no power steering. I got 1300+ psi when I shut off the p/s pressure line. I have changed the valve under the sector, replaced the front boaster. I am about out of choices, can anyone give me some advice.




[Log in to Reply]   [No Email]
red paint gotta pull

02-15-2005 05:36:04




Report to Moderator
 Re: 560 Power Steering in reply to red paint gotta pull, 02-13-2005 18:51:38  
I checked for travel in shaft and it moves in and out when you turn it. Still no p/s
Thanks for your responcse



[Log in to Reply]  [No Email]
Aces

02-14-2005 08:53:32




Report to Moderator
 Re: 560 Power Steering in reply to red paint gotta pull, 02-13-2005 18:51:38  
Red the warm shaft in the front bolster much move in and out a little in order the activate the valve. Some times the fine spline on the warm can rust tight, some times they ware bad and get pined rather than replaced. This can work but then the steering shaft must move back and forth all the way to the steering wheel. At ant rate the warm shaft muct be able to move in and out a little for the valve the operate.

[Log in to Reply]  [No Email]
red paint gotta pull

02-14-2005 08:22:51




Report to Moderator
 Re: 560 Power Steering in reply to red paint gotta pull, 02-13-2005 18:51:38  
I replaced all the u joints, there was 2 of them tight so I replaced them before I replaced the boaster. Thanks for the feedback



[Log in to Reply]  [No Email]
Hayshaker

02-14-2005 05:48:46




Report to Moderator
 Re: 560 Power Steering in reply to red paint gotta pull, 02-13-2005 18:51:38  
Maybe you have since you changed the front bolster, but if you haven't, check all the universal joints on the steering shaft. I had this on my 560 and it was the lower u-joint. $9.00 later I have good power steering.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy