TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Lesson on TA in 350U Wheatland Gas please

Welcome Guest, Log in or Register

Author

Sean in Calgary

04-12-2004 08:22:45

Report to Moderator

I haven't been on here much lately but now that I am back I am seeing a lot of questions about TA's again. I have never tinkered with mine as I try to live by the rule 'If it ain't broke, don't fix it' but at the same time if I am setting myself up for damage later by not doing some preventative maintenance, then I would rather do that then have to tear my little red work-horse apart.

Here's the deal.

Most of the time I run my tractor (a 1957 350 Wheatland Special Gas) with the TA lever pulled towards me - that is the low speed setting. When I have it thrown away in the high-speed setting I cannot shift gears or get the foot-clutch to totally disengage. Even with the clutch on the floor plate I can feel the tractor surge a little bit and there is no way I can get it to come out of gear.

Am I wearing anything with it setup the way it is? My thought was that it was inconvient and not working quite the way it was designed but at the same time this setup would ensure that I was not having clutches slipping because they could not totally engage.

Any thoughts? I do have the original owners manual, so if I need to go back over it in regards to adjusting clutches and TA then just say so. If there is a better way to skin this cat that you have learned from experience, then I am willing to take suggestions.

Thanks in advance,
Sean

[Log in to Reply] [No Email]

JLE

04-12-2004 08:49:35

Report to Moderator

Re: Lesson on TA in 350U Wheatland Gas please in reply to Sean in Calgary, 04-12-2004 08:22:45

Sean: If you have adjusted the clutch pedal to correct height, then adjust the TA linkage to release the TA. It is the short adustable link going from Main clutch shaft to the TA shaft. Shorten link one turn at a time until you overcome the release problem. It wouldn't be as book says due to some wear. It is a pain in the --- to shift with out proper adjustment. If you need more help E-M me. Jim

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy