TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Order Farmall Cub Parts Online

Cub Touch Control

Welcome Guest, Log in or Register

Author

08-06-2003 06:56:55

Report to Moderator

Hi guys,
Got my '49 Cub back together after replacing rings and crank bearings. It sounds great and oil pressure is normal. Problem is, the touch control is showing 1000 PSI at all times, even after attepting to purge system of air. I have cylinder block #354383R1. I show 1000PSI during idle, the pressure drops to 0 PSI during operation of lever forward, or lifting, and back up to 1000 PSI during operation back down. I'm using about 200lbs of weight for test.
Correct me if I'm wrong, but I should be showing little to no pressure during idle, and higher pressure during operation?

[Log in to Reply] [No Email]

scotty

08-06-2003 12:03:29

Report to Moderator

Re: Cub Touch Control in reply to EZ, 08-06-2003 06:56:55

Hey EZ, How you doin? Long time no hear! My manual on my Super A touch control has top pressure of 1100-1500 lbs. Low pressure is 15-40 lbs during idle no rockshaft movement. They do the test with 300lbs off the rear rockshaft. Glad to hear that you got that Cub straightened out. Bet your having fun with it. I had a lot of fun mowing the fields up at my Vt property. Good to hear you.
scotty

[Log in to Reply] [No Email]

08-06-2003 15:54:49

Report to Moderator

Re: Re: Cub Touch Control in reply to scotty, 08-06-2003 12:03:29

Yeah scotty,
it's been awhile for sure.
Got the Cub running nice, except after taking my longest run ever on it, about 1/4 mile, I stopped it on my lawn and could not get it to start again. No spark. After setting awhile, maybe an hour it fired up after some coaxing, but would not take the load to go. It's still out there and we're having a downpour. I moved it about 20' and got soaked.
So looks like maybe some mag coil problems and such.
But, I am very happy with this little machine so far, it's been quite a learning experience.

Hope all is well with you.
How's the Super A coming along?

[Log in to Reply] [No Email]

scotty

08-07-2003 06:41:45

Report to Moderator

Re: Re: Re: Cub Touch Control in reply to EZ, 08-06-2003 15:54:49

EZ, Super A is going ok, Im rebuilding the frontend right now. The plan is to get the front half of the tractor done by fall and roll it over to the corner of the garage until next spring when I hope to have enough money to finish the project. Talk to you soon.
scotty

[Log in to Reply] [No Email]

08-06-2003 10:00:01

Report to Moderator

Re: Cub Touch Control in reply to EZ, 08-06-2003 06:56:55

Trouble Found !!

Blocked orfice plug.
Screen was broken partly off, blew it out,
re-solder screen on, works like a charm now.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy