TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

:-) I did it :-)

Welcome Guest, Log in or Register

Author

Tom Windsor

06-01-2007 21:01:44

Report to Moderator

I removed the pto shaft in a 42 H to replace the seals in it. Then time came to put it back. I asked for and received advice on here on how to get it back in there.

So, I followed all the advice and for 3 or 4 days, at various times, I just could not get it to go back in there correctly.

So, tonight, I pulled it out and got the tape measure out...the distance from the hole up front to the surface of the entrance hole was 20 Inches. The shaft was 22 inches. SO, the light finally came on, I was trying to hit a hole that I had passed 1/2 inch earlier!!!!! It would NEVER get in there that way. So, got the shaft back in there, installed some long alignment bolts, got me a wiggle bar to slide on the shaft and started moving it towards the hole...hit it the first time!!!!! Whoopee. You just cannot beat a hard knocks college education.

[Log in to Reply] [No Email]

Dave from MN

06-02-2007 13:31:59

Report to Moderator

Sounds sickly familiar in reply to Tom Windsor, 06-01-2007 21:01:44

"SO, the light finally came on, I was trying to hit a hole that I had passed 1/2 inch earlier!!!!! It would NEVER get in there that way. So, got the shaft back in there, , got me a wiggle on the shaft and started moving it towards the hole...hit it the first time!!!!! Whoopee. "

Sounds like what the brother in law said after the first night with that nasty lazy exgirlfreind of his.

[Log in to Reply] [No Email]

City-Boy McCoy

06-02-2007 04:20:03

Report to Moderator

Re: :-) I did it :-) in reply to Tom Windsor, 06-01-2007 21:01:44

Yes, a degree from the "University of Life" is a good one to have. For me, it has been a great school; home of "The Fighting Knuckleheads". mike

[Log in to Reply] [No Email]

funderburk1

06-01-2007 21:44:31

Report to Moderator

Re: :-) I did it :-) in reply to Tom Windsor, 06-01-2007 21:01:44

Tom, glad to hear you got it in!

[Log in to Reply] [No Email]

J.J. from Afton

06-01-2007 21:42:27

Report to Moderator

Re: :-) I did it :-) in reply to Tom Windsor, 06-01-2007 21:01:44

Congrats glad it all worked for ya.

Sorry but your remark at the end reminded me of a Teddy Roosevelt quote.
"A man who has never gone to school may steal from a freight car; but if he has a university education, he may steal the whole railroad"

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy