TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

FAST HITCH problems...help

Welcome Guest, Log in or Register

Author

Clefus

05-09-2007 19:09:46

Report to Moderator

I was using a 3 btm -- 14 " fasthitch plow i recently got and I have 2 ???

1 : Someone replaced a share with one that protruded past the shin/landslide about an inch and also doesnt match up with the moldboard edge....it is a 4 bolt pattern 14 inch piece....the other two match up fine on both ends...I got a new Osmundson one at TSC and it also fits the same goofy way...
Where do I get a right one??

2: Same plow...plowing I caught something and tripped a plow back....what is the best way to re-set it.....i had a hair of a time jackin,beatin,pryin, sprayin.....

Thanks

[Log in to Reply] [No Email]

georgeky

05-09-2007 19:20:07

Report to Moderator

Re: FAST HITCH problems...help in reply to Clefus, 05-09-2007 19:09:46

The correct parts are available from IH. To reset plow just put it down on the ground and back up. If that doesnt work your trips need cleaning. I do not recommend putting oil on this as it will cause it to trip quite often. Some trips have grease fittings I would ignore those too. For genuine parts call Brad at 1-888-824-0544, he will ship them right to you.

[Log in to Reply] [No Email]

Clefus

05-10-2007 03:19:15

Report to Moderator

Re: FAST HITCH problems...help in reply to georgeky, 05-09-2007 19:20:07

THANKS Does the large bolt that the plow spins on need any certain torque?? I originally was going to remove it but didnt.... stuff was a little rusty and hard to move to reset it...i tried backing up as you said but it wouldnt go due to rust...

Where does one get info ( or manual) on setting up this plow and hitch adjustments....like draft control (the notched lever on left??? ) ?? ect...I put the tractors front and left wheel up on blocks and leveled up the plows as best as possible till the r hand fh arm screw was stopped....I have a op manual and pm manual for my 560 but may need one for the plow..
Thanks

[Log in to Reply] [No Email]

georgeky

05-10-2007 06:54:15

Report to Moderator

Re: FAST HITCH problems...help in reply to Clefus, 05-10-2007 03:19:15

To get the right manual you will need to know the model of your plow. Not sure, but you might get them here on YT at left click on tractor manuals and look. If not some are available from Binder Books and can be ordered on line. IH still has some as well. If you don't know your model no, post a picture of it here or in implement photo's and if not me, someone will know the model no. They built several different models of fast hitch plows. For plow parts you can call Brad at 1-888-824-0544. He has points,shares,shins,moldboards and even slats for them in stock in most cases. He may also have a manual.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy