TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

Need help on fast hitch

Welcome Guest, Log in or Register

Author

Mark Johnson

04-02-2007 20:49:39

Report to Moderator

I recently put a fast hitch on my SuperC.I bought a 2 point to cat1 adap.Can someone measure there fast hitch on the reciever end and then on the other end towards the tractor?The fast hitch points are 2.5in which is correct for a Superc,the reciever on my fast hitch is a little over 2.5 inches where the points go in but on the other end of the fast hitch the measurement is only 2in.So when i slide the adap in it only goes in halfway.Is the adapter point not beveled enough on the point end or has the fast hitch reciever been modified.Hope this makes sense,any help would be greatly appreciated,thanks

[Log in to Reply] [No Email]

Mark Peters

04-03-2007 12:53:48

Report to Moderator

Re: Need help on fast hitch in reply to Mark Johnson, 04-02-2007 20:49:39

Mark, The way it`s sounding to me is your hitch isn`t the problem- it`s the prong height on your adapter.I think you have the large prong (3" H)on your adapter. The prong height is measured at the thickest point of the prong, not where it`s tapering down.Without actually going out and measuring mine, I`m going to guess you`ll have to go about a foot back from the point of the prong and measure the height there.Now if that is the problem, you can either find an adapter with small prongs (2 1/2") or cut a 1/2" off the bottom of the prongs on your adapter. Hpoe this helps.Mark

[Log in to Reply] [No Email]

MM_TX

04-02-2007 21:23:33

Report to Moderator

Re: Need help on fast hitch in reply to Mark Johnson, 04-02-2007 20:49:39

I think it's about 2" toward the tractor. Is that catch buggered up?
maybe these pix will help. MM

[Log in to Reply] [No Email]

Mark Johnson

04-02-2007 21:45:19

Report to Moderator

Re: Need help on fast hitch in reply to MM_TX, 04-02-2007 21:23:33

I removed one catch competely.Can you tell me what program you use to edit your photographs with?Also what is the measurement toward the pointed end?You have the 2.5 in measurement but could you give me more measurements on the point end like distance from tip to where it starts to bevel?I would like to take a picture of my point and draw on it like you did on the picture you posted to point out my measurements.Thank you so much for all the help so far,Mark

[Log in to Reply] [No Email]

Andy Martin

04-03-2007 05:28:24

Report to Moderator

Re: Need help on fast hitch in reply to Mark Johnson, 04-02-2007 21:45:19

You can also edit photographs, add text, crop, blow up, etc. very well on Excel.

[Log in to Reply] [No Email]

MM_TX

04-02-2007 22:46:05

Report to Moderator

Re: Need help on fast hitch in reply to Mark Johnson, 04-02-2007 21:45:19

My SC is not at my house, so I can't measure until this weekend. The points stick out past the receptacle a little. I'v seen points on ebay for utilities that looked like they might not fit. The notch end looked like it didn't go to a point. I can draw them out from my draw-bar this weekend. I use Photoshop on a Mac, I do computer graphics for a living, A lot of paint type programs let you draw and type on pix. email me & I'll send you an accurate layout from an original draw-bar if you need to grind them to fit. MM

[Log in to Reply] [No Email]

Mark Johnson

04-03-2007 19:09:09

Report to Moderator

Re: Need help on fast hitch in reply to MM_TX, 04-02-2007 22:46:05

Here goes nuttin

[Log in to Reply] [No Email]

Mark Johnson

04-03-2007 22:28:19

Report to Moderator

Re: Need help on fast hitch in reply to Mark Johnson, 04-03-2007 19:09:09

try again

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy