TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

PTO Pump Installation

Welcome Guest, Log in or Register

Author

PaulW_NJ

02-22-2007 17:46:57

Report to Moderator

Someone posted a photo last month of a PTO pump installation. Don"t know why I can"t access archives for January, but would you post the photo again? Particularly interested in how it is attached and bracketed against torquing. Thanks

[Log in to Reply] [No Email]

waterpourer

02-23-2007 07:42:39

Report to Moderator

Re: PTO Pump Installation in reply to PaulW_NJ, 02-22-2007 17:46:57

I work @ Prince. All of the pictures in this thread are Prince pto pumps. Here is a link to our pto pumps page: Link

[Log in to Reply] [No Email]

PaulW_NJ

02-23-2007 04:30:36

Report to Moderator

Re: PTO Pump Installation in reply to PaulW_NJ, 02-22-2007 17:46:57

Thanks everyone! For me a picture"s worth many words!

[Log in to Reply] [No Email]

Wardner

02-22-2007 19:56:34

Report to Moderator

Re: PTO Pump Installation in reply to PaulW_NJ, 02-22-2007 17:46:57

I am probably the "somebody" you are searching for. My installation is not typical. The other photos in this thread are more in line with the instructions included with a new pump.

[Log in to Reply] [No Email]

Steven@AZ

02-23-2007 04:32:49

Report to Moderator

Re: PTO Pump Installation in reply to Wardner, 02-22-2007 19:56:34

Your installation is probably much better for these older tractors - the irons are holding the weight of the pump instead of the weight being put on the PTO shaft bearing. Nice job, I say!

[Log in to Reply] [No Email]

Steven@AZ

02-22-2007 18:34:19

Report to Moderator

Re: PTO Pump Installation in reply to PaulW_NJ, 02-22-2007 17:46:57

This is the PTO pump on our 1256. Basically you bolt an angle iron to the pump and it pushes agains the drawbar - you put a chain on the bottom of the iron to hold it from sliding back...

third party image

[Log in to Reply] [No Email]

504-2

02-22-2007 18:19:28

Report to Moderator

Re: PTO Pump Installation in reply to PaulW_NJ, 02-22-2007 17:46:57

We have one on a 560 and it has a piece of angle iron and a chain on it.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy