Posted by pburchett on May 03, 2019 at 17:59:35 from (12.182.196.81):
After rebuilding my 640 Ford I got it together enough to let it run. I let it run on and off for 20 minutes at a gentle idle up to 12 hundred RPM s. During this time I adjusted the valves, set the timing and played with the lift.
Today I let it run for another 20 minutes, mostly at 15 hundred RPM s (PTO speed) but a couple of times I let it run at wide open throttle while I adjusted the carb and a couple of times I let it run at enough RPM s to let it move across the shop floor in 1st and reverse.
Everything worked well, the lift goes up and down, the clutch is smooth, the engine purrs like a kitten, no smoke, no blow by.
I shut it down to find a puddle of engine oil the size of a saucer under the tractor. The rear main seal is now leaking bad. I used the Fel-Pro crank shaft seal kit with the 2 piece rubber seal (which I staggered like the instructions said) and the rubber packing material with drive in pins. I siliconed the rubber side packing sections, but tried not to get any on the round seal halves.
Unless someone has a suggestion I guess it is time to tear the tractor back apart and reinstall a seal from beneath the engine. This task I do not look forward to as it appears that I will have to remove the crank from the bottom.
Should I clean and reuse the seal and packing and really silicone the time out of it or get a new seal? I still have the oil absorbing packing and rope seal that came with the engine gasket kit, but I thought those were nothing but trouble. Any suggestions would be appreciated as I read all I could before installing the seal the last time, and now I am really bummed out.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Harvestin Hay: The Early Years (Part 2) - by Pat Browning. The summer of 1950 was the start of a new era in farming for our family. I was thirteen, and Kathy (my oldest sister) was seven. At this age, I believed tractor farming was the only way, hot stuff -- and given a chance I probably would have used the tractor, Dad's first, a 1936 Model "A" John Deere, to go bring in the cows! And I think Dad was ready for some automation too. And so it was that we acquired a good, used J. I. Case, wire tie hay baler. In addition to a person to drive th
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.