Posted by charles todd on September 15, 2009 at 19:46:53 from (205.242.95.137):
For those reading that do not know or have forgot here is the skinny. The clutch suddenly would not release clean and I had a lot of gear clash. I suspected the 15-20 year old clutch (4-pad button) or pressure plate had failed or seperated. I had adjusted the linkage until I gave up and ordered the parts to do a clutch R&R.
Today I revisited the Farmall 504 in search of the problem. Tomorrow I had planned to trailer it to my fathers and split it. My parts are still arriving to the dealer tomorrow, but I'll inventory them until the clutch fully fails. I'll just set them aside by the re-surfaced flywheel I have...
Here is what I found. Mechanical diesels are wonderful, just pull out the fuel shut-off cable and crank away. I bumped the tractor over and crawled underneath MANY times looking for a sign, a sign that I was not going to have to split tomorrow. Well I found it... I'll let the pictures describe.
What is this?
And this?
Supposed to look like this...
Here is the fix...
I adjusted the clutch linkage and the TA linkage. Then I started the engine and gave it the test. Pressed in on the clutch and within 5-7 seconds, could shift clash free... That partially out pin was dragging the clutch even with the take-up against the throw out bearing in the disengaged position (clutch pedal up). If you look at the last two pics, you'll see that I am not done. I still have to adjust the release finger stud. It appears to have worked out and it is dragging against the throwout bearing. The other two finger have sufficent clearance.
Any tips on setting the finger? Or should I just "guess-timate" to match the other two? Dad said the previous pressure plate had done the same, except the cotter key did not disappear.
Clutch R&R:
Clutch, Pressure Plate, Throw out Brg, Pilot Brg, Rear Engine Main Seal and Sleeve, $300
Cotter Key from work, FREE
Experience Learned, PRICELESS...
Thanks guys,
CT
This post was edited by charles todd at 19:50:07 09/15/09.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Chores - by Frank Young. The ceaseless passing of time! It is at once our friend and our enemy. It measures our progress and it makes us old. Like most features of our life, few things are all good or all bad, and most such judgments depend on our own perspective or viewpoint. In our particular hobby, we enjoy the nostalgic return to the days of our youth as we recreate many of the scenes that took place on the family farm that served as the stage for the first few acts of the play that is our live
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.