Posted by Stick welding on September 09, 2012 at 22:31:52 from (96.53.210.246):
Finally had a dry weekend where I could finish building my heavy duty scarifier for the 3 pt. hitch. It's made out of 14" wide flange that's somewhere around 105lbs./ft and has 15 backhoe teeth adapters welded on. Welding the adapters on had no problems other than they were made for a 1" edge and the beam I had was only 3/4". I had a gap to fill and used 2 passes of 3/16" 7018 after filling the gap. I cranked the heat (amps) up and they welded really easy.
Fast forward to welding the 3 pt. mounts on. They are the ones cut on a $250,000+ CNC plasma table. First I had to use a die grinder to ream the holes a little for the pins to fit. Then I prefabbed the uprights with a 2" spacer separating them. I had to grind the edges of the spacer flat because it had about 5 deg. angle on the cuts. The uprights also had an angle on the cut and made it a pain to line everything up. I got it lined up but after tacking all the mounts in place, I took out the 3/16" rods and proceeded to weld them on. I put the ground right on the mounts but sure got a lot of arc blow. The rods started off great but on just about every pass, they would act up about 3/4 of the way to the end. I'd start off with a normal 15 deg. rod angle and have to change to about a 15 deg. push angle to counteract the arc blow. I've had arc blow before but never like this. Usually after you get the first pas in, the second pass goes pretty smooth. What's puzzling is that I didn't have any problems with arc blow welding the adapters on and I used more heat. 4th gear at about 85/90 on a SA200. Maybe if I had the rods in an oven and wrapped the ground cable around the beam would have helped? It's never going to break so I didn't experiment too much but luckily I had a sharp chisel to clean the spatter when it acted up.
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
