|
Ford 9N, 2N & 8N Discussion Board |
Re: I'm Back - question about starter selenoid.
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by souNdguy on July 08, 2004 at 06:41:02 from (12.77.214.151):
In Reply to: I'm Back - question about starter selenoid. posted by Rich in Michigan on July 08, 2004 at 06:22:21:
The oem 3 terminal solenoid is an easy finagle. It mounts to the starter.. one big terminal faces the front of the tractor.. one big terminal faces the back of the tractor.. the small terminal faces the engine.. in fact... it is so close it is hard to get a tool in there to take the nut off. Power from the battery connects to the terminal towards the rear of the tractor. The terminal towards the front of the tractor connects to the copper buss bar strip over to the starter post. The big thumb switch wire connects to that small third terminal... all there is to it. The thumb switch wire is simply switched ground. If you want to do some meter readings.. hook up power to the big rear terminal.. use your vom and see if you measure power on the small third terminal ( you should ) if so.. you are hooked up correctly.. and grounding that small terminal should make the solenoid close, and then you should be able to read power on the front terminal that passes power to the starter. If it is not an oem 3 terminal solenoid... that info above may not apply. If it is a gm alternator that conforms to the 10-Si specs we use.. then.. if it is a 3 wire job: P1 is isolated/switched excite. That is.. you are providing power to start the initial charging. A momentary toggle switch from this terminal to + will work, or a marker lamp in line with this terminal, then hooked to the switched side of the ignition switch should work.. You could also substitute a correctly sized diode in place of the marker lamp ( oriented correctly ).. or even an automotive style ignition switch could be used.. and hooking P1 to a contact seperate from the ignition.. like a accy position that is powered when the ignition is on.. but off when the ignition is off. P2 is hooked right down to the output stud.. this is the sensing line for the VR. Soundguy
Follow Ups:
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
Home
| Manuals
| Parts
| 12-Volt Kits
| Carburetors
| Radiators
| Engine Kits
| Videos
| Books
Copyright © 1997-2008 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you use antique tractors, collect antique tractors, or just enjoy looking at antique tractors, welcome to our site! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 antique tractor forums, show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|