Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Harry Ferguson Tractors Discussion Board

brakes and sure seals are done!


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by gshadel on January 10, 2006 at 05:58:48 from (69.215.227.130):

third party image

I finally finished installing new sure seals and new brakes. It was a bigger job than I had thought.
I removed old sure seals, greased the bearing and installed new seals. It actually looked like the oil leakage was coming more from between the shims, bolts, and hub gasket (or lack of gasket), than from the axle seals.... but, once I had started, there was no turning back.

Installing the new sure seals was fast & easy using my "sure seal install tool" (a piece of 3" PVC pipe). see link. I also heated-up the hub up a bit by sitting it in front of my reddy heater, and froze the new sure seals in the freezer before installing. Don't know if it helped, but the seals started right in with a couple good wacks on the PVC pipe. Then I switched to a lighter hammer to tap in the seals so I didn't overshoot the seal depth in the hub.

I also found that each axle had a different arrangement of shims & gaskets compared to the backing plate and hub. I installed the shims between the backing plate and axle housing, and made paper gaskets to go between the hub and backing plate. I used a thin coating of silicone around the hub to try to insure no oil gets into the brakes again.
Now I can lock-up the rears easily when I stomp the brakes!
What fun!
I also had a nice puddle of steering box oil on my garage floor that dripped out over several days.... going to have to do something about that some day...



Replies:




Add a Reply

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract. ... [Read Article]

Latest Ad: Super WD9. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy