(800) 853-2651
SHOP NOW

John730D, ?? about your electric remote valve

F

farmermatt

Member
I saw your picture you posted last month of your electric valve multiplyer. I think I found what you had at surplus center, just curious if it all works like you expected. Im looking for a similar set up. $149 sound like the price on your valve? Any problems or limitations??
Thanks
Matt
 
Yes. It works just like it should. The only limitation I have now is the coulpers are not breakaways. Need to be careful not to put any pull on the hoses. This has not been a problem, but you need to be aware of it.

I got the valve from Suplus Center and I also got the o-ring to NPT adapters from them. I built my own control box using a SPDT switch and indicator lights. The valve is ground isolated so using it on a positive ground tractor is not a problem

I mounted the valve to the back of the power-trol control by removing the four top screws and replacing them with one inch longer bolts. I spaced the mounting plat out by using shaft collar locks. This gave me enough room to mount the selector valve. The extra room also helped when I hooked up the hoses.

Now All I have to do is select the set of hoses I want to use with the switch and then I can still use the original control lever for the remote cylinder.

I have used it on a pull tpye box scraper that has hyd. lift and hyd. tilt. Really works good.
 
Here are the pictures again
c2428_sml.jpg

c2430_sml.jpg

c2429_sml.jpg
 
Take a look in community album on left side of this page. I uploaded them from there and they got smaller. If you need, I could e-mail them to you. Thanks!
 
Hey John,

Yes, please send me a e-mail as I'd like to chew the fat about your project, if'n you don't mind.

T_Bone
 
Thanks for the info, so I take it the SAE 8 ports they spec translates to the O-ring type. Guess Ill need 6 of those adapters. Mine is going on a 7700 Ford so I guess Ill need a different can of paint than you used!
 
John, we better go this way as I haven't recevied anything yet

T_Bone99 "at" dedac "dot" com

T_Bone
 
You must log in or register to reply here.

Similar threads

B
Farmall 350 Fast Hitch and Hydraulic Remote Questions
Replies
10
Views
2K
Bill VA
B
D
Rebuilt voltage regulator
Replies
7
Views
989
Jim L WA
J
A
Need advice 2N purchase
2
Replies
27
Views
3K
Caryc
C
Ultradog MN
It wasn't meant to be. - Long post
Replies
16
Views
1K
Vito
Vito
M
9N 3-Point Rotary Mower Questions
Replies
9
Views
914
Northvale PA
N
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top