(800) 853-2651
SHOP NOW

Wico Magneto Website

M

Mathias NY

Well-known Member
Is there a good website for Wico magneto specification and applications? As I understand the XH series, they were essentially the same magneto, with different dwell settings for the various applications.

I have an XH1113 (for an Oliver crawler) that I would like to adjust for an Allis Chalmers B. This is a low budget project, so I am trying to avoid buying parts where ever possible.

Thanks for the help.
 
Try www.smokstak.com, its and antique gas engine
and steam engine site. There are several different
catagories, including one on magnetos, where you
can ask questions, and lots of knowledgeable
people answer.
I have a WICO, master parts book, about 6 inch"s
thick, gives directions on how to do it, and specs
for different engines. I"ve never done it, but
think it"s just a matter of adjusting the stops
that trip the impulse. A test stand may be
required to do it right. My e-mail is open, send
an e-mail and i"ll copy those pages and forward
to you.
 
(quoted from post at 07:47:30 01/08/09) Try www.smokstak.com, its and antique gas engine
and steam engine site. There are several different
catagories, including one on magnetos, where you
can ask questions, and lots of knowledgeable
people answer.
I have a WICO, master parts book, about 6 inch"s
thick, gives directions on how to do it, and specs
for different engines. I"ve never done it, but
think it"s just a matter of adjusting the stops
that trip the impulse. A test stand may be
required to do it right. My e-mail is open, send
an e-mail and i"ll copy those pages and forward
to you.
Click to expand...

Hi. I have an Allis B with this WICO XH1113 mag and it does not run smooth. Can you scan in the pages of your book that refer to this modifications to make it work with an Allis B? I do not think my mag was set up correctly in the first place.
Many thanks..
Another 'old tractor fanatic'
Bob T
 
You must log in or register to reply here.

Similar threads

I
Oliver Super 88 transmission
Replies
6
Views
296
super99
super99
C
Ford 2N and 8N Magneto Options
2
Replies
39
Views
3K
Den N Ms
D
J
Help deciding first project - Ford 9N vs Allis-Chalmers
2 3
Replies
40
Views
3K
rustred
rustred
F
AC WD Hydraulic System
Replies
3
Views
797
DrAllis
D
A
Wico XH 1042 Magneto Magnet Rotor Rub
Replies
1
Views
447
jd man wis
J
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top