(800) 853-2651
SHOP NOW

Massey Ferguson 2200 backhoe


More info would help. What hydraulic lines are you asking about? Description location, pictures might help.

Steel tubing, hoses, or hoses with steel tubes on the ends might have different answers and suggestions.
 
A little of all of the above rubber hoses have 90 degree turn to lift cylinders both sides seem to be male 4 in all about 18 inches in length. The back ones go from rubber to tubing, not real good with terminology and assuming it will need high pressure.
 

It is most likely your hoses will be high pressure two wire braid hose. It is common to take old hoses to a shop or parts store and have them copy the old one to make a new one. Some replacement hose ends have bends but those are generally 6" long or less.

Are the hose made with the tubing as part of the hose end fitting or is the hose connected to the tubing with a threaded fitting? If you have a hose with a longer tube made to the hose end fitting, you may need to have the old tubing cut off and either a compression or a weld/braze hose end fitting is used to attach old tube to the new hose. If you have damaged steel tubes running along a frame there are shops that can make them. If just a spot leaking sometimes they can be welded or brazed at that location to seal them. Often people replace the tubing with hoses.

Some pictures of what you need to replace could allow tailoring this to your needs better.

Your tractor is a 2200. Look for tags on the loader and backhoe to see if you can find out what models they are, which might allow looking at parts books for them.
 
Thanks for your help I will look for model numbers but they will be under many coats of paint and rust . Thank you for the info it is greatly appreciated.
 
Most lines will separate from the hoses with threads though a few wanted to make more money and save on connections to leak by not having them do that. So then you have to either replace them with a new hose the length of the whole thing or find a place to put ends on the lines to fit a hydraulic fitting.
 
You must log in or register to reply here.

Similar threads

D
Massey Ferguson 2200 rear grinding noise
Replies
7
Views
290
Dscicluna1
D
M
Massey Ferguson 393
Replies
1
Views
137
used red MN
U
C
Looking for some OEM part numbers. 202 Massey
Replies
8
Views
243
Jim.ME
J
Smithlake
Power steering ford 655A backhoe
Replies
8
Views
277
Smithlake
Smithlake
B
  • Question
Wain Roy Backhoe
Replies
2
Views
246
Andy Wickiser
A
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top