(800) 853-2651
SHOP NOW

champ forklift CB50

D

dave321

New User
Hello
I have a champ forklift model CB50 with I think a failing hydraulic pump. I have loosed the lines , removed two bolts ; it wiggles , but will not come out/off.
Any ideas ?
 
We need more information about the fork lift. You will need to have 5 posts, or ask permission
(site comments to the left in classic view) to post pictures. They would help. Is the hole big
enough to get a drive gear out of. Id there an access panel on the other side? Maybe a front
engine Cover If you pull it out and a gear drops off the shaft you will be in far more difficulty.
Jim
 
(quoted from post at 16:19:37 07/23/22) Hello
I have a champ forklift model CB50 with I think a failing hydraulic pump. I have loosed the lines , removed two bolts ; it wiggles , but will not come out/off.
Any ideas ?
Click to expand...


On the support of the seat is a tag :

CHAMP
corporation
El Monte , Califorina. 91733

MODEL : CB 50

Serial number : CC735683

It has a flathead engine

This post was edited by dave321 on 07/24/2022 at 03:38 pm.
 
(quoted from post at 16:19:37 07/23/22) Hello
I have a champ forklift model CB50 with I think a failing hydraulic pump. I have loosed the lines , removed two bolts ; it wiggles , but will not come out/off.
Any ideas ?
Click to expand...


---------------------------------------------------------------------------------------------------------------------------------------------
July 26
This might help someone else.
I scraped most of dirt and oil off around the hydraulic pump. The pump bolts to an aluminum plate that bolts to the engine. I originally unbolted in the wrong place. Once the aluminum plate is unbolted , the pump , plate, and gear come off.
I will take it to a hydraulic shop tomorrow for testing , if not to obsolete. He says on the phone for me to pull the gear so he can see the shaft. It may be to obsolete for his equipment.
It has a tow bar. I may have to reassemble and tow to his facility ( 20 some miles away ,0 for him to test the pressure ; or figure a way for me to test ; with it attached to the engine in the forklift.
 
You must log in or register to reply here.

Similar threads

1
Hi I need to tune up my 1987 Champ Telehandler Forklift
Replies
4
Views
229
used red MN
U
M
Case 446 lawn tractor
Replies
1
Views
247
Klyde
Klyde
RBnSC
Forklift battery charging Question
Replies
10
Views
697
gene bender
G
O
Allis Chalmers 621 Rough terrain forklift opinions
Replies
4
Views
325
oldfarmall
O
stevieb49829
Update on a couple of related things
Replies
0
Views
526
stevieb49829
stevieb49829
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top