(800) 853-2651
SHOP NOW

Ford 901 fenders

N

Nick Q

New User
Im looking for at least one set of the 01 row crop fenders but really need 2 sets if anyone has some the would like to part with
 
At least you can still get new ones. Not like the 900 fenders.
I do not have any of either available. Sorry.
 
(quoted from post at 19:06:58 07/30/21) At least you can still get new ones. Not like the 900 fenders.
I do not have any of either available. Sorry.
Click to expand...


Can't you notch an 800 fender?
 
I wish I had know about this place.
I used mig, metal and fabricated panels to fill in rust. Then used bondo to finish.
10 years later you can't tell I repaired fenders.

In my younger years I learned the meaning of the word WORK doing body work on cars.
 
> I wish I had know about this place.
> I used mig, metal and fabricated panels to fill in rust. Then used bondo to finish.
> 10 years later you can't tell I repaired fenders.

George, I think my fenders are too far gone to repair, so I plan to put new skins on my old brackets. I think the Steiner fender skins are actually from Dennis Carpenter. I don't know why YT doesn't carry them as they do have a lot of DC stuff. I buy most of my parts from Steiner, because they're only 40 minutes from my house.

I have a BIL who does decent body work. It's not something I have the patience for.
 
It's not something I have the patience for.

I'm retired and always up for a challenge.
Rebuilding a dana 411,
replacing a $20 bearing instead of paying for a new pto clutch.
I have tools and love to use them.
If I need a tool to do a job, good reason to buy one.

I would have bought a skin if I knew they were available.
 
The only issue I have is the tractor didnt come with fenders so I dont have the brackets to install on the new skins.
 
(quoted from post at 07:13:29 07/31/21)
(quoted from post at 19:06:58 07/30/21) At least you can still get new ones. Not like the 900 fenders.
I do not have any of either available. Sorry.
Click to expand...


Can't you notch an 800 fender?
Click to expand...
No. Unfortunately, they are not the same. Not close to the same curves.
They will bolt on and work functionally, but they're not the same.

mvphoto79503.jpg
 
You must log in or register to reply here.

Similar threads

crsutton81
JD 3020 wheel spacing & fenders
Replies
1
Views
204
Fixingfarmer
Fixingfarmer
D
Tractor tires
Replies
6
Views
535
Denteen
D
J
JD M fenders
Replies
6
Views
415
ChrisInPA
C
M
56 Ford 900 pedestal sector shat and pinion
Replies
2
Views
147
showcrop
showcrop
R
D-14/15 Fender Hack
Replies
2
Views
332
rasman57
R
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top