(800) 853-2651
SHOP NOW

Ford 7000 row crop to utility fenders

L

Loganthefordy

Member
Would anyone have any ideas on being able to put row crop fenders on a utility that previously had clamshells on it? How to mount it and if it would even work in general? Thank you!
 
I would think the brackets;U bolts;axle houseings etc would be the same.Only the fender itself would be different.Just bolt em on.
 

Row crop fenders will fit utility tractors, if you installing them on a 5000 or 7000 they work fine, if your installing them on a small tractor they will be nearly to tall
The later flat top fenders are adjustable for height but the early row crop fenders are not
 

Dont know what the width is but its wide enough to work on 4000, 5000 and 7000 axles
Dont knot if the bolt hole slots are long enough for the smaller 2/3000 axles
What are you wanting to put them on
 

The fenders are separate from the platform so you can install them by theirselves and position them on the axle where you want them.
You can put them one at the same position the clam wheels were if you like that setting
 
Ok thank you for the help! Do they mount on the axel with a piece of square tubing welded to the fender and the u bolt? This should be the last question, thank you all for the help!
 
Hey, if you commented on my post about 7600 fenders I did not see it, I got a notification about it and didnt see anything. Could you send it again please? Thanks so much!!!!
 

The flat style fenders used on the -600 series will work on your 7000 but be aware that unlike the early row crop fenders that were one piece the newer flat fenders are two pieces that allow them to be adjusted for height.
I have a set on my 4000

mvphoto72793.jpg
 

No I've never measured them, never had the need to measure them since they are universal fit for any of the square tube axles on the 2000 thru 7000 models.


mvphoto72801.jpg



mvphoto72802.jpg
 
You must log in or register to reply here.

Similar threads

S
Jd 2520 row crop running poorly
Replies
6
Views
458
Sweecy
S
F
Oliver 77 rear axle bearings
Replies
4
Views
196
FarmersWife2022
F
W
WTB loader 19-124 for 1958 Ford 961-5 (Row Crop)
Replies
1
Views
100
showcrop
showcrop
D
Ford 981 vs 901
Replies
5
Views
395
Dwarner
D
T
Ford 7000 flywheel mounted pump
Replies
6
Views
357
Destroked 450
Destroked 450
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top