(800) 853-2651
SHOP NOW

is there any direct replacment engines for a ih dt429

J

jbradshaw93

New User
i am trying to find out if there is any engines that are a direct fit replacement for an international harvester dt429 its in a 250b track loader. any information will help i have spent coutless hours on internet with no information at all. anything will help thank you
 
Isnt three a 4100 or a 4156 farm tractor around ,or a 70 Hough loader used that engine also what happened your got a cracked block? i am also thinking the the 436 IHC engine will bolt up to the bell housing !! Thats what they used in the 4166,, there should be a lot of them around!!!
 


intake gasket went bad and filled engine completly full of water and froze during winter. didnt know till spring went to start and found out. i am in washington by everett. not as many of the tractors out here but i am still doing research on the daily to locate an engine. my father bought a school bus with a 360 ih and looks like going to have to build an adapter plate to fit. but cant realy find any information on the dt429 about what bolt pattern is on the back of the block. or if any other engines are the same. so thought i would see if anyone had any information on here
 
Well is that going to be big enough,i am almost positive the 436 will bolt up to the bell housing, and the smaller 407 Family engine too, seen a 429 in a 806. There is a company out in Pa, that builds bell housing adapters,but you shouldn't need one with the 436!
 
You are wasting your time the dt 360 will just barley move that 250 around and will not be able to
do any work. I have seen a few MACK truck engins put in the td 20 dozer but your best bet might be a 250 c
engine it would bolt right in. The man you need to contact is Tony Collins at 731 225 0154 he has
years of ih experience and can get you going.
 
You must log in or register to reply here.

Similar threads

S
Best Practices for IH Wet Sleeve Engines (886, 986, 1066, etc.)
Replies
16
Views
856
JIM MN
J
H
IH574 Gas Tractor with a 3/8" Bolt in the Carburetor Outlet
Replies
9
Views
398
stevieb49829
stevieb49829
hdokes
'60 D6b steering issues
Replies
8
Views
582
hdokes
hdokes
F
Case IH 585 new clutch won't disengage
Replies
15
Views
1K
showcrop
showcrop
S
Which 300 series engines can replace the 4219T?
Replies
7
Views
1K
sovste22
S
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top