(800) 853-2651
SHOP NOW

Cub Cadet 7532

1

1070Michael

New User
More of a modern tractor, but I have a Cub Cadet 7532 with the hydrostatic transmission. I got it after it has sat outside under a tarp for 12 years. I got most of the bugs worked out and have it running
well. It has a rear pto and manual says w/ the hydrostatic transmission it is a live pto. My problem is when i push in the clutch and try to engage the PTO i just get grinding, i have to just force pto into
gear by a hard grind. I can't start the tractor with PTO engaged, it is too smart. Any ideas what my problem might be. I'm not even sure what a clutch does on a hydrostatic transmission. Is my clutch
not allowing pto to engage? Any ideas. What should i look at to get PTO fixed, so it goes smoothly into gear.
 
I am not certain, but there could be a switch on the dash that turns on and shuts off the PTO. The lever might disengqage it. OR the clutch might be frozen on. Google the 7532 PTO clutch. Jim
 
I have a CC 7000 straight gear drive but similar to yours.The rear PTO can be engaged at any time without using the clutch,that's weird that they would have changed it.
 
Went out and checked mine out apparently you have a mechanically engaging PTO,what may be the problem is the clutch just needs to be adjusted.Once the PTO is
engaged if you shove the clutch all the way down does the PTO shaft stop running?
 
Another thought after looking at a parts breakdown for my tractor is the PTO disc is stuck after sitting so long.Is the clutch for the tractor and PTO or just the PTO since its a hydro? If just the PTO then you could put a tiller on the tractor and hold the clutch down while tilling might break it loose.
 
I think you may be right, when i disconnect the clutch rod, it moves pretty easily. Kinda tells me it's not engaging the clutch. Now how to free it up?
 
You must log in or register to reply here.

Similar threads

M
Need Some Assistance!
Replies
11
Views
979
BarnyardEngineering
BarnyardEngineering
S
International Cub Cadet Mower Model 2206
Replies
4
Views
273
steve_in_mo
S
W
John Deere 2130 bearing pieces floating around rear end
Replies
3
Views
213
Westcoast
W
D
Cub Cadet 122 . Has anyone made their own hydraulic lift ?
Replies
16
Views
564
Janicholson
Janicholson
P
IH 544 hydro PTO
Replies
3
Views
258
BarnyardEngineering
BarnyardEngineering
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top