(800) 853-2651
SHOP NOW

Skytrak lift with Ford diesel engine

K

kito169

Member
Hello. My friend has a Koehring Skytrak forklift with a Ford diesel engine. It quit running so he removed the injector
pump and had it rebuilt. There were broken springs inside among other issues. I'm trying to help him reinstall the pump
but can't find any external timing marks to align. The rebuilder said to set the engine to 6 deg btdc. I assume this
number on the right lower side of the block is the model of engine D4NN6015J. All help is greatly appreciated. Also, has
anyone used searchmanuals.net and let them install their app on your computer? I'm leary of all stuff others want to put
on my computer. Thanks, Rick
 
Fords are a bit different to time if you could not set them in time when you removed the pump,, Fastest way I found is to pull the valve cover, and turn the engine to the TDC marks, been 20 years since I did a Ford but it was on the flywheel I think on a 5000, I do not remember them being on the damper pulley but again its been 20 years,, anyway turn to TDC (top dead center) and check # 1 push rods and see if both are loose, if not turn one turn to tdc again and recheck, when both are loose back up half a turn then turn to your timing degree install pump,,
 
I appreciate your comments but there aren't any timing marks on the flywheel. The bell housing has no openings to show them. There is no pointer or markings anywhere front or rear,that we can find.
 
If has round CAV pump it will only go on one way. Just put back to where paint is on plate. There is marks on flywheel,get rusty and are hard to find/see.
 
Kito169,
Look at the ford forum here on yesterdays tractor.
Look for posts by "bern".
He recently made a post on how to time a diesel that would be VERY helpful to you in this situation.
HTH
Keith
 
You must log in or register to reply here.

Similar threads

Hdonly
Toro 223D with Mitsubishi L3E engine
Replies
10
Views
293
jrsavoie
J
T
English Ford Industrial Diesel Engine
Replies
13
Views
2K
Eman85
E
J
Injector lines to fit 67 Ford 5200 with 233 CI Engine
Replies
3
Views
220
Destroked 450
Destroked 450
G
Trying to figure out which diesel engine I have in Ford 445 tractor, 175, 183, or...?
Replies
6
Views
409
Destroked 450
Destroked 450
F
1968 Ford 4000 Compression Pressures
Replies
9
Views
384
FishDuck
F
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top