(800) 853-2651
SHOP NOW

Oil capacity

B

Bigmac03

New User
Would someone be so kind to tell me how much oil my 1954 NAA will hold. My dip stick is broke off so i have no clue. The block number is EAE-6015-F if that helps also where is the best place to ordr parts? Thanks in advance.
 
As per the NAA owners manual the engine holds 5 quarts plus one quart if you change the filter and yes I just looked in the owners manual I have for the NAA
 
If that dipstick is broke off so that the broken part is in the tractor get it out before trying to put any oil in as the broken part could coust you a complete engine.
 
Old,
I use a Microguard filter on my Jubilee. It holds a pint. Microguard is only filter that doesn't drain back on tractor.
 
Thank yall a million. Im not sure if the broken part is in the tractor or not i just inherited it and have been running it. Now if I could just figure out the lift id be complete
 
Get a good strong magnet and put it on the bottom of the oil pan. If the end of the dip stick is still in there the magnet will keep it from moving around and causing a problem.

As for the lift well ask away I'm sure some one can help you. I know if it has to do with what would be in the owners manual and I see if I'll try to answer your questions
 
Old,
I read that on your first post.
I was hoping to pass along to those there is a better filter for NAA and it half the size.

I use full synthetic in Jubilee and can get about 200 hrs on oil change. Oil stays clean looking for a long time. It doesn't use a drop either.
 

My lift will move about an inch when u raise the handle all the way up but if you push the handle outward and up the lift will raise all the way.
 
The broken part might work its way to the drain plug so you could get ahold of it with a pair of pliars and pull it out. If not use that magnet.
 
(quoted from post at 22:45:51 09/24/18) Just curious if anybody had any info on my lift issues?
Click to expand...
sir you probably get better response's if you start your on thread a lot of people will never see your question here good luck with your tractor sorry I'm no help on it
 
You must log in or register to reply here.

Similar threads

F
Ford 600 Motor
Replies
3
Views
443
Andy Wickiser
A
olgentdc
12 valve95 Dodge bent oil pan ,,.
Replies
13
Views
459
olddavid
olddavid
T
International Harvester IH 300 Utility - pipe in oil pan
Replies
6
Views
381
thorn197
T
O
Oil level rising
Replies
9
Views
441
OregonAaron
O
S
Oliver 1650 oil change
Replies
14
Views
806
sonnythomas
S
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top