(800) 853-2651
SHOP NOW

Sound a use for welding gloves with a hole in fingers

Geo-TH,In

Geo-TH,In

Well-known Member
Cut the fingers off and slide glove over arm. It protected my arm from welding sparks up to the elbow.
a197693.jpg
 
Good idea ! I'd of never thought of that.
Sure would of helped me from getting a bad burn years ago when I had HOT metal go right above the glove.
 
Plan to take the next pair of bad gloves and cut it off above the fingers and attach it to today's cutoff gloves. After a while I'll have a glove that goes all the way up my arm. I don't mind wearing a welding jacket in the winter, not the summer.

Now is this redneck, cheap or just frugal?
 
I tried that with some imported fiber gloves once a few years ago, still recovering from the burns...
Just kidding, that's a darn good idea
 
You never know when you need an extra thumb to hold something when welding. Comes in very handy.
 

Do you have a source for leggings to keep slag out of your boot tops when wearing shorts?
 
(quoted from post at 04:34:37 08/07/15)
Do you have a source for leggings to keep slag out of your boot tops when wearing shorts?
Click to expand...

Flip-flops work better with shorts. That way you can just dance until the slag falls of the top of your foot.
 
I don't wear shorts or flip flops, especially when I'm welding or riding a MC.

I also have to wear long sleeves because I'm so sweet, the critters will eat me alive.
 
(quoted from post at 09:32:37 08/07/15)
(quoted from post at 04:34:37 08/07/15)
Do you have a source for leggings to keep slag out of your boot tops when wearing shorts?
Click to expand...

Flip-flops work better with shorts. That way you can just dance until the slag falls of the top of your foot.
Click to expand...

Hey, that sounds like a good solution! LOL.
 
You must log in or register to reply here.

Similar threads

T
Bucket for loader
Replies
6
Views
582
Geo-TH,In
Geo-TH,In
Fixingfarmer
Decent rock shaft lift arm puller?
Replies
8
Views
661
Fixingfarmer
Fixingfarmer
3
Welding rods left out in the rain
2
Replies
30
Views
2K
Keith Molden
K
P
Need a hexigon shaft for AC disc
Replies
4
Views
257
timcasbolt
timcasbolt
A
3020 Drawbar Pin Hole
Replies
4
Views
493
ss55
S
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top