(800) 853-2651
SHOP NOW

are loader joystick controls re build-able?

M

morgan in ar

Member
I have a customer who wants me to come look at his Kubota L2600 tractor. He says that the joystick is very sloppy and loose, and has been for sometime. He said that He could always tell that it didn't go all the way back to neutral, and the pump would run against the stop (probably on the bucket tilt back). Now he says that the loader up and down, as well as the bucket tilt are very slow, and he has to hit just the right spot on the controller for them to work at all. He said revving the tractor didn't seem to make a difference. I also asked him about the three point hitch, and he said it seems to be working normal. I don't have any experience with joysticks, so any help would be greatly appreciated. Thanks -Morgan
 
Open tractor , or with a cab? Cab type often use cables from joystick to control, open tractors can just have linkage on the control. My 585 CaseIH open tractor had a joystick mounted on the control, and it got so wore that the loader worked just as you have stated. New linkage was my cure.
 
Yes, need more information, but the lever control itself, and or the linkage to the valve, have replaceable parts if its something like a Nimco, which was on our challenger tractor that eventually had similar problems, the parts were expensive for that one and it was literally just the nylon pivot or ball ends on them that failed. There is a pivot post on the Nimco joystick handle, and a nylon ball inside. Not all that impressed with the materials used. Here is a diagram and photos of that one. Snow collapsed the roof and contributed to the problem with that one, as you can see the crack, but it had issues prior I think. Annoying as heck when using the forks as I recall.
a172189.jpg

a172191.jpg

a172192.jpg
 
Morgan Yes.. the L 2600 is not offered in a cab. It has a basic Kubota loader with the valve controlled by linkage right there at the operation point. Going to take four end and pins and a couple of ball joints. Any good KUBOTA parts man will be able to sell you what you need.
 
You must log in or register to reply here.

Similar threads

I
Cab loader controls
Replies
12
Views
459
Texasmark
T
W
Broke the loader joystick
Replies
8
Views
903
Blackhole49
Blackhole49
Mike440i
440i with 71 loader and pippen backhoe
Replies
6
Views
312
Mike440i
Mike440i
F
Dunham Lehr Inc/Farmhand 22 Loader Bucket Measurements
Replies
17
Views
719
ford4wd08
F
R
John Deere 5410 with 541 Loader Hydraulics
Replies
0
Views
129
Ron Stazick
R
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top