(800) 853-2651
SHOP NOW

MH44 EFI Might be celebrity

D

David G

Well-known Member
I sent pictures to the manufacturer of the controller for my EFI project. He said they are going to post a picture on Facebook tomorrow. I went out for a drive tonight, it is actually running so good I am getting a little bored.

I will let you know if it goes, and the post.
 
After all that work and head scratching I bet that is a great feeling. I'm glad it is all working out for you.
 
I can see it now.

"David G invents EFI kit for old tractors. The EPA mandates all OLD tractors have to have EFI and particulate filters if ran in the low 48 states."

LAMO.

David I am glad you have it going. Your WAY over my head when your talking about what and how you made it work. When working around this newer computerized stuff I feel pretty dumb at times.
 
I actually found a catalytic convertor for $50 that fits right on the stack, would love to see the emissions report.

The only issue with emissions I have is that I am running 9:1 compression with no EGR, doubt that would pass on NOx
 
David STOP !!!

I already have my worry beads and garlic out to ward off your Technology from seeping into my head!!!

LAMO
 
If you lived New York State, they probably make you put an EVAP system on. Can not have a vented gas tank in this state. The way things are going with state emissions test you have to learn how fix your car or truck yourself. The other option is take to a repair shop. If you go the shop route have a pocket full of hundred dollar bills or a high limit charge card.
On the positive side, I am glad you got the 44 running decent. It is quite an accomplishment.
 
Here is an earlier post I forgot about

https://www.facebook.com/diyautotune/photos/pb.57837395932.-2207520000.1405480185./10152048360290933/?type=3&theater
 
You must log in or register to reply here.

Similar threads

super99
super88 update
Replies
14
Views
715
GermantownGreen
G
B
I.H. model 674 239 engine diesel
Replies
5
Views
301
Brent Zappe
B
R
My son impressed me-a little long
Replies
14
Views
1K
redtom
R
T
Roll pins-cheap and unreliable?
Replies
9
Views
966
John Garner
J
V
new owner of a 620, will try to update this as we go.
2 3 4
Replies
61
Views
3K
valiant8086
V
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top