|
| |
| Tractor Pulling Discussion Forum |
Topic: Re: stroke crank for farmall
[Show Entire Topic] [Return to Forum]
| Author |
[Modern View]
|
| awchevy
02-04-2013 17:02:19
66.87.145.30
|
I'm just trying to figure out if I need tovgring my cam for clearance if I got with a 5.5 it 5.75 stroke. If I use aftermarket rods. I've been looking at murpheys. I just need to know what to stroke my crank to.
|
|
|
| Tim Yates
02-04-2013 18:09:07
71.171.21.185
|
|
Re: stroke crank for farmall in reply to awchevy, 02-04-2013 17:02:19
|
|
| Murphy's can have the cam clearanced for you. It will still be plenty strong.
|
|
|
| Mike n Mo
02-04-2013 17:15:14
64.134.41.92
|
|
Re: stroke crank for farmall in reply to awchevy, 02-04-2013 17:02:19
|
|
| | Call and talk to Jeff at Murphys. I'm pretty sure he's got a stroker kit available for the H-350 series engine with the crank/rods/pistons and cam. He can tell you what you'll need for a particular stroke. Mike
|
|
|
| awchevy
02-05-2013 10:14:26
66.87.144.157
|
|
Re: stroke crank for farmall in reply to Mike n Mo, 02-04-2013 17:15:14
|
|
| OK thanks. If I pull the sleeves out of a 350 block hat sizes pistons do u recommend running? And in a 300 block can you pull the sleeves and put a oversize bore 350 sleeve?
|
|
|
| H-66
02-05-2013 17:09:56
166.181.83.186
|
|
Re: stroke crank for farmall in reply to awchevy, 02-05-2013 10:14:26
|
|
| If you are pulling the sleeves out of a 350 or 300 block 3.8125" is the bore size to use unless you are going to hard block it. How much do you want to spend? If you want 5.75" stroke call Murphys he will set you up for less money in one stop than you will spend trying to piece it together yourself.
|
|
|
| awchevy
02-05-2013 19:19:06
70.197.193.168
|
|
Re: stroke crank for farmall in reply to H-66, 02-05-2013 17:09:56
|
|
| How big can you run with it hard blocked?
|
|
|
| H-66
02-06-2013 17:04:02
166.181.82.148
|
|
Re: stroke crank for farmall in reply to awchevy, 02-05-2013 19:19:06
|
|
| Not sure how far you can go with hardblock, I have not tried it yet. Gary Baker could point you in the right direction there. Also Jeff down at Murphys will have more insight than me.
|
|
|
| Mike n Mo
02-05-2013 10:48:54
13.8.123.100
|
|
Re: stroke crank for farmall in reply to awchevy, 02-05-2013 10:14:26
|
|
| AWchevy, Can't help on piston size to use, I'm not that familar with the H-350 engines. I'm close to Murphy's shop and stop in there every now and then, so I have some knowledge of what he's got going on there. Good luck with your project. Mike
|
|
| [Show Entire Topic]
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
