| Ford 9N, 2N & 8N Discussion Forum |
Topic: OT-16hp Briggs I/C motor
[Return to Forum]
| Author |
[Modern View]
|
| G6 at Snook, TX
02-19-2013 07:02:02
64.92.181.22
|
Where would I find the model/serial number off of a Briggs 16hp I/C motor? I have looked, but have not found a plate or impression. The motor is attached to a Lincoln Weldanpower 225.
|
|
|
| G6 at Snook, TX
02-19-2013 17:53:50
69.39.48.218
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 07:02:02
|
|
| Found it. I had pulled the carburetor and taken it to them. Anyhow, it was stamped into the shield next to the plug. Had to wire brush it up good to read it.
326437-758-01 8506241
This post was edited by G6 at Snook, TX at 17:54:17 02/19/13.
|
|
|
| G6 at Snook, TX
02-19-2013 12:43:55
64.92.180.162
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 07:02:02
|
|
| I am at work now. Check it tonight again.
|
|
|
| G6 at Snook, TX
02-19-2013 09:52:14
64.92.182.136
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 07:02:02
|
|
| I need the model number for the carburetor. It needs a rebuild badly and I have sent it in to a local Briggs shop for repair, and they need to order the right kit.
|
|
|
| billy boy2
02-19-2013 13:14:16
72.251.9.158
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 09:52:14
|
|
| Quoting Removed, click Modern View to see
If the Briggs shop doesn't know or can't find the model # are you sure you want them to rebuild your carb? If they're stamped, and there's a little rust/oil/grease/dirt, they may have to scratch around a little to find them.
|
|
|
| Bob
02-19-2013 11:50:20
64.255.159.192
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 09:52:14
|
|
| So you are not seeing it at either of the two locations the red arrows point to in the illustration?
|
|
|
| pconnie..ks.
02-19-2013 09:25:22
66.87.4.154
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 07:02:02
|
|
| if you cant find it..i have the same welder..hth phil
|
|
|
| G6 at Snook, TX
02-19-2013 08:17:40
64.92.181.22
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 07:02:02
|
|
| Bob
02-19-2013 07:53:20
64.255.159.192
|
|
Re: OT-16hp Briggs I/C motor in reply to G6 at Snook, TX, 02-19-2013 07:02:02
|
|
| | It will be stamped into the sheet metal "cowling" around the flywheel. Is the engine a flat twin? 
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
