|
| |
| Ford 9N, 2N & 8N Discussion Forum |
Topic: 9N/8N Sherman
[Return to Forum]
| Author |
[Modern View]
|
| James Trovillion
11-25-2012 07:44:13
50.40.246.234
|
|
| James Trovillion
11-28-2012 03:24:43
50.40.246.234
|
|
Re: 9N/8N Sherman in reply to James Trovillion, 11-25-2012 07:44:13
|
| Thanks to all who replied, hope to never quit learning Jim T
|
[Reply] [No Email] | |
| John Smith8N
11-25-2012 08:43:41
75.23.68.179
|
|
Re: 9N/8N Sherman in reply to James Trovillion, 11-25-2012 07:44:13
|
| Yes, it will fit. If it is a step-up/step-down combination there are no worries about it having the wrong gear. They never made any of those with straight cut spur gears.
|
[Reply] [No Email] | |
| TheOldHokie
11-25-2012 08:59:36
108.22.203.30
|
|
Re: 9N/8N Sherman in reply to John Smith8N, 11-25-2012 08:43:41
|
|
| John Smith8N said: (quoted from post at 12:43:41 11/25/12) Yes, it will fit. If it is a step-up/step-down combination there are no worries about it having the wrong gear. They never made any of those with straight cut spur gears. |
That's intertesting. Can the spur gear input shaft be installed in a combo unit for use in an older 9N? Or is it simpler to swap the transmission as well?
TOH
This post was edited by TheOldHokie at 09:00:27 11/25/12.
|
[Reply] [No Email] | |
| John Smith8N
11-25-2012 11:32:09
75.23.68.179
|
|
Re: 9N/8N Sherman in reply to TheOldHokie, 11-25-2012 08:59:36
|
| Quoting Removed, click Modern View to see
The input shafts for the step-up and the combination are not interchangeable. Original installation instructions for both the step-up and the combination state that if you have an early 9N with spur gears you must replace the 9N7113 gear in the tractor's transmission with a 2N7113 helical gear before installing the Sherman. That's the only change required.
|
[Reply] [No Email] | |
| HCooke
11-25-2012 07:56:12
70.195.64.206
|
|
Re: 9N/8N Sherman in reply to James Trovillion, 11-25-2012 07:44:13
|
| I will fit just fine unless it has a very rare straight cut gear. For more info see John Smith's web site.
|
[Reply] [No Email] | |
| TheOldHokie
11-25-2012 08:36:09
108.22.203.30
|
|
Re: 9N/8N Sherman in reply to HCooke, 11-25-2012 07:56:12
|
| Quoting Removed, click Modern View to see
And if it does have the straight cut spur gear input shaft it is a rarity that you can likely sell for a premium to some one that needs it. Use the proceeds to buy one with the helical input gear for your 8N and pocket the difference.
TOH
|
[Reply] [No Email] | |
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
