Author	[Modern View]
Steven24 09-05-2012 20:53:26 108.205.42.124 Report to Moderator	Lift will not go all the way down when engaged. The lever is all the way down and still will not Go all down. The draft controls have been switched and the problem is the same. [Reply]   [No Email]
JMOR 09-06-2012 20:12:47 72.181.173.171 Report to Moderator	Re: Lift will not go all the way down in reply to dhamps10, 09-05-2012 20:53:26   I can't see the geometry of shredder hool up or tires/wheels on your tractor, etc. If stock size tires & wheels, then range of travel of ball sockets at end of lift links is 8.5 to 34.25 inches (total travel is 25.75 inches). Measure your top, bottom, and total travel. [Reply]  [No Email]
JMOR 09-06-2012 19:48:54 72.181.173.171 Report to Moderator	Re: Lift will not go all the way down in reply to horsin around, 09-05-2012 20:53:26   Steven24, what defines "all the way down" for you? [Reply]  [No Email]
Steven24 09-06-2012 19:57:04 108.205.42.124 Report to Moderator	Re: Lift will not go all the way down in reply to JMOR, 09-06-2012 19:48:54   With a shredder on, the shedder is about 8 inches off the ground. Even with no implements on. [Reply]  [No Email]
Royse 09-06-2012 15:30:10 69.36.49.151 Report to Moderator	Re: Lift will not go all the way down in reply to Bob Harvey, 09-05-2012 20:53:26   If it's an 8N, try flipping the position control lever under the right edge of the seat to the horizontal (draft) position and see if they go down. [Reply]  [No Email]
Steven24 09-06-2012 19:45:32 108.205.42.124 Report to Moderator	Re: Lift will not go all the way down in reply to Royse, 09-06-2012 15:30:10   This happens in both position. [Reply]  [No Email]
ZANE 09-06-2012 14:08:33 98.83.100.58 Report to Moderator	Re: Lift will not go all the way down in reply to Steven24, 09-05-2012 20:53:26   I have a friend whose lift did that and when I looked at it I discovered that the stabilizer bar brackets pins were in the wrong holes and making the geometry of the lift arms bind up when he tried to lower the lift. Took a while to convince him of the error but finally did and he fixed it and then had to make longer stabilizer bars. The first ones were shop made. Zane [Reply]  [No Email]
Steven24 09-06-2012 19:47:39 108.205.42.124 Report to Moderator	Re: Lift will not go all the way down in reply to ZANE, 09-06-2012 14:08:33   The stabilizer bars are off. [Reply]  [No Email]
soundguy 09-06-2012 04:49:35 173.107.232.190 Report to Moderator	Re: Lift will not go all the way down in reply to Steven24, 09-05-2012 20:53:26   what's this on? 8n? naa? 00/01+ [Reply]  [No Email]
Steven24 09-06-2012 19:46:36 108.205.42.124 Report to Moderator	Re: Lift will not go all the way down in reply to soundguy, 09-06-2012 04:49:35   49 8N [Reply]  [No Email]