(800) 853-2651
SHOP NOW

12 volt conversion pictures

C

Carl Young

New User
I bought an alternator conversion for my 8N, side distributor tractor but the kit did not have instructions for mechanically mounting the alternator, just a generic picture that looked like a car mount. I know that somewhere on the Internet, there must be pictures of a correct
conversion but I can't find any.

Any guidance would be appreciated.
 
do you have a fax machine?
i can fax you a wiring diagram?
i havent figured out scanning and email yet but i can try too, just know how to use a fax so it would be quicker.
 
Here is a picture i found under that parts and pieces
hope this helps
Marty
v5395.jpg
 
Thanks for the reply. I found the schematic, now I need a picture of the mechanical mount for a late 1952, 8N.

Carly
 
make a bracket out of angle iron and flat strap that uses the oem left side genny mount holes.. fpr the top bracket you have a few choices.. get a universal top bracket with an adjuster slot.. then use a water pump bolt.. or a headbolt if you have to.. I prefer setups that don't use headbolts..

soundguy
 
Thanks to all that submitted pictures.
Jonallgrow's picture used the same brackets that I received in the kit. I have found a great resource in this forum. As you might have guessed, I'm not mechanically inclined and a picture IS really worth a 1000 words.

Carly
 
Marty........nice clear picture of the 4-nipple frontmount with r/h side alternator. Unfortunately, the later 8N 5-nipple sidemount distributor is gonna be in the way, which is why ALL sidemount alternators are mounted on the RIGHT side. .......Dell
 
I've always have trouble marching for my drill Sargent until he made me carry a rock in my right hand. (grin) .......Dell...... hup-one, hup-two.....about face MARCH!!!

Marty........nice clear picture of the 4-nipple frontmount with r/h side alternator. Unfortunately, the later 8N 5-nipple sidemount distributor is gonna be in the way, which is why ALL sidemount alternators are mounted on the LEFT side. .......Dell
 
You must log in or register to reply here.

Similar threads

J
JMOR, A resistor question.
2
Replies
35
Views
1K
JMOR
J
P
300 u 6 volt gen to 12 volt alternator condition question
Replies
8
Views
461
Paul 300 U
P
R
john deere 4020 12 volt conversion problem
Replies
2
Views
222
Jim.ME
J
R
6-12 volt update points conversion?
Replies
17
Views
575
Janicholson
Janicholson
H
Stuck Clutch or Rusty Shift Rails or something Else Jubi
Replies
15
Views
820
HanknotFrank
H
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top