Author	[Modern View]
big Mo 02-03-2013 18:11:40 70.194.80.14 Report to Moderator	How big of a motor can you make out of a 670 block 800 heads [Reply]   [No Email]
newby puller 02-05-2013 21:37:28 174.255.80.110 Report to Moderator	Re: pulling motor in reply to big Mo, 02-03-2013 18:11:40   I have a set a 403 jugs bore to 5.5 sleeved and hard blocked never been installed yet anyway [Reply]  [No Email]
Jeff Gravert 02-05-2013 20:28:51 174.39.167.170 Report to Moderator	Re: pulling motor in reply to big Mo, 02-03-2013 18:11:40   6.125 by 7.75 makes 913 cid. 800 parts are the only possible way to make that combo work. I have been itching to make one of these and if you got the money, I've got the time. Even with these inefficient old bastards taking around three cubes to make a horsepower that is still a pretty good ride. Past that a person needs to be building a LSS or LLSS. [Reply]  [No Email]
big Mo 02-05-2013 00:10:30 70.194.72.171 Report to Moderator	Re: pulling motor in reply to big Mo, 02-03-2013 18:11:40   Jeff what's the bore and stroke for 900. Can you build one 1000. Looking to beat up on some 460 with red diamond motors. [Reply]  [No Email]
6pack 02-05-2013 14:20:26 64.85.139.248 Report to Moderator	Re: pulling motor in reply to big Mo, 02-05-2013 00:10:30   If you are looking for a crank, I have one 7.625" I have not decided if I am gonna use it or not.... I might stay at 7.00-7.25... It was welded by Jeff @ Stamm Equipment, and never used. Now for the bad news... It will need to be re ground as it was set up for U rods which will not work!!! Would have to do a custom rod... Give me an email address if interested, can send some pics too... This crank cost $2500 originally! [Reply]  [No Email]
RnRPerformance 02-06-2013 10:57:55 166.137.89.164 Report to Moderator	Re: pulling motor in reply to 6pack, 02-05-2013 14:20:26   6Pack I am interested in the crank if it's still available. Send me an email. Thanks. Ryan [Reply]  [No Email]
6pack 02-06-2013 12:16:55 64.85.139.248 Report to Moderator	Re: pulling motor in reply to RnRPerformance, 02-06-2013 10:57:55   Reding64@gmail.com [Reply]  [No Email]
PullerMMU 02-06-2013 03:59:07 38.123.14.49 Report to Moderator	Re: pulling motor in reply to 6pack, 02-05-2013 14:20:26   $2500 for that crank? Sounds like you got screwed. I had one welded up and turned for about half that much. [Reply]  [No Email]
6pack 02-06-2013 05:59:25 64.85.139.248 Report to Moderator	Re: pulling motor in reply to PullerMMU, 02-06-2013 03:59:07   MMU where can you get a crank stroked 1.625" for $1200? Is it still together? Is it a backyard weld job? Bobby Hinton told me about a hack shop that are just welding blocks on to the journals and grinding them down and out the door they go! They do not last long I did not have this crank done... It was another puller that had it done never put it together and lost interest, his loss my gain!! I do know that around my area, guys are getting over $100 for every 0.100" of stroke added, 1 shop will not even quote it, it is a flat rate $80 until it is done... [Reply]  [No Email]
PullerMMU 02-06-2013 06:22:17 38.123.14.49 Report to Moderator	Re: pulling motor in reply to 6pack, 02-06-2013 05:59:25   Hapco Terre Haute, IN 812-232-2550 You got screwed. [Reply]  [No Email]
MMMMMMMMMMMM 02-05-2013 04:35:50 38.123.14.49 Report to Moderator	Re: pulling motor in reply to big Mo, 02-05-2013 00:10:30   MM heads will not flow enough to feed a 900 cid 4 cylinder motor. 1000 cid is a total waste of money unlees your main goal is to brag on how big your motor is. [Reply]  [No Email]
6pack 02-04-2013 05:42:12 64.85.139.248 Report to Moderator	Re: pulling motor in reply to big Mo, 02-03-2013 18:11:40   I am gathering parts for a 5.50" bore X 7.625" stroke, Jeff G. Is putting the 800 jugs on a 670 crank case for me. Real good guy to talk to. I would say this is an average build... Some smaller and some a lot bigger!! Rick [Reply]  [No Email]
Unstylish 02-10-2013 18:02:32 76.253.110.105 Report to Moderator	Re: pulling motor in reply to 6pack, 02-04-2013 05:42:12   6pack? I dont know Jeff G, and this isnt a question of his ability...but why on EARTH would you have work done in nebraska when you have a mm shop in dorr , 15 miles one way, who could do it and one of the best mm builders down in south haven, 15 miles the other way?? [Reply]  [No Email]
brentp4455 02-04-2013 09:17:29 70.194.7.123 Report to Moderator	Re: pulling motor in reply to 6pack, 02-04-2013 05:42:12   is it true there are recast jugs being made? how big can they go? [Reply]  [No Email]
Shawn W 02-04-2013 15:13:05 50.40.116.32 Report to Moderator	Re: pulling motor in reply to brentp4455, 02-04-2013 09:17:29   go look on the pulling page and scroll back a few pages, i asked on there couple weeks ago and the guy that makes them put his number and name up there. [Reply]  [No Email]
Jeff Gravert 02-04-2013 04:43:39 98.135.58.198 Report to Moderator	Re: pulling motor in reply to big Mo, 02-03-2013 18:11:40   How big is directly related to the depth of your pockets. 900 cid is pretty big. Jeff [Reply]  [No Email]