|
| |
| Minneapolis Moline Tractors Discussion Forum |
Topic: ut clutch
[Return to Forum]
| Author |
[Modern View]
|
| ktp460
07-25-2012 11:23:21
98.17.194.178
|
|
| J Wuertz
08-01-2012 12:13:14
74.36.114.184
|
|
Re: ut clutch in reply to ktp460, 07-25-2012 11:23:21
|
| You would have to change the seat in order to get your foot on the clutch also.
|
[Reply] [No Email] | |
| LW
07-26-2012 16:18:59
76.5.182.158
|
|
Re: ut clutch in reply to ktp460, 07-25-2012 11:23:21
|
| I have a UTI set up and it will work in a utu
|
[Reply] [No Email] | |
| Ktp460
07-26-2012 16:32:38
67.141.20.95
|
|
Re: ut clutch in reply to LW, 07-26-2012 16:18:59
|
| Would you sell the uti set up
|
[Reply] [No Email] | |
| t.r.k.
07-26-2012 09:04:28
70.61.106.182
|
|
Re: ut clutch in reply to ktp460, 07-25-2012 11:23:21
|
| | I may be against the grain here: If the pivot for the clutch release in the bell housing is in the same place, (THAT is a Big 'If') Then, It probably would be possible to put a foot clutch in a UT, but would need flywheel and perhaps starter, as well as clutch shaft, clutch shaft bearing cover with the sleeve for the release bearing to slide on, throwout bearing, throwout bearing return spring and whatever it hooks to, release fork, release fork shaft as well as new linkage back to the clutch pedal which would probably have to be fabricated. It'd be the same difference between a UTS clutch and a UTI clutch. You were asking a 'possible' not a practical question weren't you?
|
[Reply] [No Email] | |
| ktp460
07-26-2012 12:33:34
98.17.194.178
|
|
Re: ut clutch in reply to t.r.k., 07-26-2012 09:04:28
|
| I am new to MM what I have is a uts with a 425 on it. I would like to put a foot clutch in it. Does a uti have a foot clutch? Could i use parts from a uti in a uts?
|
[Reply] [No Email] | |
| brian koeman
07-25-2012 19:04:06
75.40.240.212
|
|
| jd plowboy
07-25-2012 17:50:29
69.160.179.227
|
|
Re: ut clutch in reply to ktp460, 07-25-2012 11:23:21
|
| i dont think so
|
[Reply] [No Email] | |
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
