|
| |
| John Deere Tractors Discussion Forum |
Topic: G blowby update
[Return to Forum]
| Author |
[Modern View]
|
| bigboreG
11-11-2012 07:02:53
166.181.3.214
|
Thought id let you know what i have found so far. Checked compression, book calls for 65 i have 74 on both sides. So were good there. The breather is ok, but the oil pipe going to the tappet cover was plugged. This pumps oil to the tappets correct? Is this the only source of oil they get on a G as opposed to the A with its galley thru the block and head? Also can i just remove fork and pulley to check the drain back hole or does the reduction cover have to go as well?
|
|
|
|
| bigboreG
11-11-2012 10:19:22
166.181.3.106
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 07:02:53
|
|
| Only drain back i see is at bottom of main case bout a 3/4 hole. Is there one on the pulley itself?
|
|
|
| bigboreG
11-11-2012 13:35:12
166.181.3.73
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 10:19:22
|
|
| Alright i found what i was looking for. Thanks Ron
|
|
|
| BushogPapa
11-11-2012 12:59:28
173.88.51.117
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 10:19:22
|
|
|
NO, it is a small hole in the bottom of the Groove on the "Seal(?)" that the "spiral" slings oil inside of..that IS all there is to this...!! Ron..
|
|
|
| Old Popper
11-11-2012 08:49:00
216.51.202.134
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 07:02:53
|
|
| If you need to move the wheel for clearance, I took the rim off the cast disk to gain room enough to take the pulley off mine. I don't know what it would take to move the hubs on the axles.
|
|
|
| BushogPapa
11-11-2012 07:47:04
173.88.51.117
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 07:02:53
|
|
|
You can remove the Clutch and Fork to get to the drain-back groove..
Hope your rear tire is set out far enough...
I cannot give any information on the rocker oiling on a "G".. Ron..
|
|
|
| mbdeere
11-11-2012 07:45:18
184.63.147.142
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 07:02:53
|
|
| You will be able to clean it by removal of the pulley only and of corse the stuff that needs to be removed to get the pulley off.
|
|
|
| mbdeere
11-11-2012 07:44:01
184.63.147.142
|
|
Re: G blowby update in reply to bigboreG, 11-11-2012 07:02:53
|
|
| You will be able to clean it by removal of the pulley only and of corse the stuff that needs to be removed to get the pulley off.
|
|
|
| bigboreG
11-11-2012 09:36:37
166.181.3.148
|
|
Re: G blowby update in reply to mbdeere, 11-11-2012 07:44:01
|
|
| Thanks all. The wheels are all the way out, lucked out there!
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
