Author	[Modern View]
wijim 10-27-2012 14:26:55 166.182.3.218 Report to Moderator	Ok so we picked up a f125 2 bottom today put on the tractor and it won't pick it up without helping a little. When it is up it stays there.Is there a bypass that can be adjusted on the powertrol? Tha engine does not labor when picking it up.Thanks, Jim [Reply]   [No Email]
Wilamayb 10-27-2012 19:45:29 75.253.150.146 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 14:26:55   I would perform a pressure check on your scv. If it is up to pressure I would leave it be. The B was not suggested by Deere to be used with the 800 hitch, and for good reason. Even if you get the B to pick it up you won't be able to keep the fronted on the ground. A 44 plow will suit the B. if you insist on a mounted plow get a 50 or an A. [Reply]  [No Email]
wijim 10-27-2012 18:55:23 99.148.63.68 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 14:26:55   I shimmed it more then I should and it still sounds like it is bypassing.Is ther anything else to look for? The plow is up in the air to see if it settles overnight. [Reply]  [No Email]
Lon in NE 10-27-2012 16:54:23 24.246.208.56 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 14:26:55   Can we say aluminum can??? It's easy to cut and THIN! There will be no wear, it just takes up space. Lon [Reply]  [No Email]
wijim 10-27-2012 17:14:30 166.181.3.171 Report to Moderator	Re: 48 B and plow in reply to Lon in NE, 10-27-2012 16:54:23   I just measured the thickness of the shims that were in there subtracted the thickness of a washer and added enough thin shims to bring it back to original and added 2 more shims. we'll see if that works here in a minute. [Reply]  [No Email]
gtx1967jewison 10-27-2012 15:28:31 174.253.132.249 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 14:26:55   You need the Owners manual. Its in there. Also, a larger diameter cylinder is the best approach, as it gets alot heavier when stuck in the ground. Make sure you have 30 wt oil in the powertrol also. [Reply]  [No Email]
wijim 10-27-2012 15:33:44 166.182.3.249 Report to Moderator	Re: 48 B and plow in reply to gtx1967jewison, 10-27-2012 15:28:31   Its a mounted plow and we run Hyguard in everything. Thanks [Reply]  [No Email]
wijim 10-27-2012 15:17:59 166.182.3.245 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 14:26:55   I have parts and service manual and neither have adjustment info. [Reply]  [No Email]
wijim 10-27-2012 15:27:27 166.182.3.233 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 15:17:59   I think I found the proper adjusting screww. But they talk about removing/adding washers to adjust the presure that I don't find in the books i have any help would sure be nice. Thanks, Jim [Reply]  [No Email]
wijim 10-27-2012 16:36:23 166.181.3.104 Report to Moderator	Re: 48 B and plow in reply to wijim, 10-27-2012 15:27:27   I did some searching and found where the presure relief valve and spring are now to find some thin washers. [Reply]  [No Email]