Author	[Modern View]
Roger in Iowa 05-19-2012 11:48:22 166.182.3.80 Report to Moderator	SCV on my 1971 leaks high pressure to marker cylinder on 7000 planter. Have to hold lever activated down to prevent marker from raising while planting. How much is it going to cost me? Poppets, seats, etc, and labor (will vary I understand). Looking for ball park $$. Thanks, [Reply]   [No Email]
Tx Jim 05-20-2012 17:18:16 67.142.163.22 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Hotflashjr, 05-19-2012 11:48:22   Mike You're correct thanks for correcting me. Oldtimers disease(CRS) got me again This post was edited by Tx Jim at 17:19:04 05/20/12. [Reply]  [No Email]
Tx Jim 05-20-2012 12:36:11 67.142.163.25 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Justin in mt, 05-19-2012 11:48:22   Quoting Removed, click Modern View to see Roger it's been several years since I sold/service 3020/4020 tractors but I think if you remove parts key #13 you can put SCV in float on a '71 3020 [Reply]  [No Email]
Mike Aylward 05-20-2012 13:45:31 216.145.134.145 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Tx Jim, 05-20-2012 12:36:11   Jim, I believe no. 13 is a rubber piece that locks the lever in place, such as using a hydraulic motor or a separate loader valve. It has no function on the float. This is done at the linkage of the SCV. Mike [Reply]  [No Email]
Tx Jim 05-20-2012 04:30:30 67.142.163.23 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Walt in Jaxn Tn., 05-19-2012 11:48:22   Roger Have you tried reversing the hose to the other side of same SCV? RE10924 KIT, SCV OVERHAUL ADD 49.09 USD AR86535 VALVE, POPPET ASSEMBLY ADD 52.00 USD 208.00 USD R65501 SPRING ADD 2.95 USD 11.80 USD *Total 268.89 USD [Reply]  [No Email]
Roger in Iowa 05-20-2012 10:23:04 166.182.3.72 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Tx Jim, 05-20-2012 04:30:30   Yes, I have tried the other side of the SCV. Other SCV has the same problem but double acting cylinder and larger on the lift of the planter doesn't cause as much of a problem. No float position as mentioned as a solution. Is SCV linkage mis-adjusted. Or do they all not have float position. 2nd SCV is not original to the 3020. THX [Reply]  [No Email]
Mike Aylward 05-20-2012 12:06:16 216.145.134.145 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Roger in Iowa, 05-20-2012 10:23:04   Roger, there is a float position available on these tractors (and the older ones as well). Place the linkage rod at the SCV in the other hole, then place your lever fully forward. Mike [Reply]  [No Email]
Jared in wi 05-19-2012 19:20:39 184.158.84.33 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Roger in Iowa, 05-19-2012 11:48:22   Poppets are around $50 a piece. Seal kit is about $50 as well. Four puppets are needed and one seal kit. Approx. $250 in parts, and the labor will vary, but will range from $250 to $350. Additional parts will vary depending on what is found once it is disassembled. Total bill should be around $600. Where are you located, I have many years of experience reconditioning these. Email is open if you have any additional questions. [Reply]  [No Email]
JMS/.MN 05-19-2012 14:56:50 24.159.214.198 Report to Moderator	Re: $$ to overhaul SCV?? in reply to Roger in Iowa, 05-19-2012 11:48:22   Seems like the kit, maybe with cage, was around $100 a few years ago. Have you tried it in float? [Reply]  [No Email]