4020 Front Drawbar Support

Anonymous-0 · Mar 23, 2010

I need to get the front drawbar support off of my early 4020. The holes are wallowed out pretty bad on the ears where the draft links mount. Do I have to pull the loadshaft all the way out to get the drawbar support off? Is it possible to drill out the holes where the draft links mount and put bushings to tighten it up?

DONMYEIL · Mar 23, 2010

Yes you need to pull the shaft. There are bushings in the yoke, hopefully you havent went to far and wore the holes. A machine shop might make bushings for it.

Anonymous-0 · Mar 23, 2010

Don there were no bushing in the yoke on 4020s maybe 71 and 72 models

430WLPG · Mar 23, 2010

Do you have a casting number? I have a couple NOS yokes

TIMAR · Mar 23, 2010

I have mine at a machine shop as I am writing this. I am having them put the drawbar hole bushings in and 1.16 bushings in the outer holes for the 3pt arms. I'll post back later and tell you how it turned out. You'll have to drive out the pin in the front also to get the support off. Just look first to see which side of the pin is mushroomed and drive from the other side.

Anonymous-0 · Mar 24, 2010

Draw bar supports can be bought new from mother deere,you might try a salvage yard

DAVIS FARMS · Mar 24, 2010

Draw bar supports can be bought new from mother deere,you might try a salvage yard

DONMYEIL · Mar 24, 2010

Oh sorry I wonder what R26502 for early and R71476 for late are for??

DONMYEIL · Mar 24, 2010

I forgot to say that I have only changed a few of these.

Anonymous-0 · Mar 24, 2010

So are you saying that Deere has bushings for this? Did it have bushings in it from the factory? I don't see them, but it's hard to tell with it on the tractor.

DONMYEIL · Mar 25, 2010

Yes they are there just hard to see.

Tx Jim · Mar 26, 2010

(quoted from post at 11:01:54 03/25/10) Yes they are there just hard to see.

DONMYEIL
Are you positive there are bushings in the holes where 3pt arms attach? I could find any on JD's website. I found bushings for frt pin,drawbar & load control shaft but not 3pt.

Tx Jim · Mar 26, 2010

(quoted from post at 16:46:20 03/24/10) Oh sorry I wonder what R26502 for early and R71476 for late are for??

load control shaft holes not 3pt hitch attaching holes.

TIMAR · Mar 27, 2010

Only the later ones after 259,0?? ser.no had the bushings.

Tx Jim · Mar 27, 2010

(quoted from post at 07:17:22 03/27/10) Only the later ones after 259,0?? ser.no had the bushings.

May I ask what the part #s are for the bushings for holes that 3pt draft arms attach? I can't find a part # on JDparts.com for such a bushing for this application. Granted 4020's had a part # break @ SN 259740 & up for a different front drawbar support. Thanks

4020 Front Drawbar Support

Anonymous-0

Well-known Member

DONMYEIL

Member

Anonymous-0

Well-known Member

430WLPG

Member

TIMAR

Member

Anonymous-0

Well-known Member

DAVIS FARMS

Member

DONMYEIL

Member

DONMYEIL

Member

Anonymous-0

Well-known Member

DONMYEIL

Member

Tx Jim

Well-known Member

Tx Jim

Well-known Member

TIMAR

Member

Tx Jim

Well-known Member

Similar threads