|
Support YT
Subscribe Today!
|
| John Deere Tractors Discussion Board |
Topic: taper lock flywheel removal
[Return to Forum]
| Author [expand] |
[Modern View]
|
| MBdeere
11-07-2009 11:38:32
75.105.222.127
342409
|
Does anyone have any pictures of the three pieces to a taper lock flywheel not installed. I would like to better understand how they are made. Im just not having any luck getting mine off.
|
|
[Reply]
[No Email] |
|
| Ryan Nagele
11-08-2009 15:59:52
98.132.211.244
342531
|
|
Re: taper lock flywheel removal in reply to MBdeere, 11-07-2009 11:38:32
|
| If it came loose, chances are the thrush washer came out of place and needs to be replaced.
|
[Reply]
[No Email] |
|
| mjbrown
11-08-2009 14:11:41
70.198.152.183
342523
|
|
Re: taper lock flywheel removal in reply to MBdeere, 11-07-2009 11:38:32
|
| I think I may have used a couple of splitting wedges between the flywheel and the case. I was careful and didn't damage anything but I had visions of a broken maincase spinning in my head. Not the way I wanted to get it off but nothing else was working.
|
[Reply]
[No Email] |
|
| JOHN DEERE 70
11-08-2009 09:26:19
192.249.47.164
342509
|
|
Re: taper lock flywheel removal in reply to MBdeere, 11-07-2009 11:38:32
|
| I would try to retighten it I"ve seen them come loose before.They cost 800. plus shipping or more . I found instructions on this forum. First make sure your oil slinger is line up and bushing is all the way in for tolerance purposes.First but a bottle jack between the tire and the bolt on the crank in the center of the clutch assembly and put some pressure.Put on the flywheel then hit the rib ONCE with a 16# maul then tighten nut.Hit again ONCE tighten the nut and so on til the nut will no longer tighten.(TO REMOVE)place jack the same way and back off nut til it"s just past the taper lock (the end of the threads)so you don"t mess threads up.Lay a thick piece of flat steel on the nut and hit the steel with a 16# maul.GOOD LUCK.
|
[Reply]
[No Email] |
|
| Ryan Nagele
11-07-2009 18:58:07
98.132.211.244
342455
|
|
Re: taper lock flywheel removal in reply to MBdeere, 11-07-2009 11:38:32
|
| After the flywheel is off, use a gear puller
|
[Reply]
[No Email] |
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
Home
| Manuals
| Parts
| 12-Volt Kits
| Carburetors
| Radiators
| Engine Kits
| Videos
| Books
Copyright © 1997-2008 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you use antique tractors, collect antique tractors, or just enjoy looking at antique tractors, welcome to our site! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 antique tractor forums, show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
