Author	[Modern View]
john chris 08-10-2012 21:11:59 71.87.212.93 Report to Moderator	iam lookings for some parts for ih 200 manure spreader gound driven gears [Reply]   [No Email]
Bret4207 08-12-2012 08:06:52 64.19.90.196 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-10-2012 21:11:59   Let me guess- you need the big apron chain drive gear because the teeth are stripped? The IH 200 uses type "S" apron chain, not 67 or 67H like most other spreaders. People unknowingly replace the S with 67 and next thing you know apron chain teeth are stripping. [Reply]  [No Email]
john chris 08-12-2012 09:12:22 71.87.212.93 Report to Moderator	Re: ih 200 manure spreader parts in reply to Bret4207, 08-12-2012 08:06:52   no chain it a gear that clicks and runs the bed chain turns bed shraft thanks [Reply]  [No Email]
Bret4207 08-13-2012 18:00:32 64.19.90.196 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-12-2012 09:12:22   Yeah, that's what I was talking about. The APRON chain, bed chain as you call it, is a type "S", If someone replaced it with a 67 or 67H then the apron chain will not match the drive sprocket and will climb up on the sprocket making the drive gear strip the teeth. Most folks can't tell a 67 from an S without comparing them side by side. If the drive gear is stripping teeth, check that. You'll see the "bed" chain climb out of the drive notch in the sprocket and up onto the hump on the sprocket. Sometimes only one side will do it and then the chain runs crooked too. If that's happening you either need to get an "S" apron chain of switch your sprockets. The teeth in the drive gear can be revamped with an angle grinder and some patience. Worked for me. If you have all the pieces a good man should be able to braze it back together. It can be reinforced too. Finding a good used part isn't a huge problem as there are lots of 200's around. Getting the thing apart is the problem. I've located 3 over the years and so far every gear has broken trying to get it off. Maybe if you can find one and get the owner to let you cut the whole axle off to get to the gear and then heat the whole thing and put it a press. I can tell you gear pullers and propane torches aren't enough. Getting the wheel off to get to the gear is enough of a chore, by itself. This post was edited by Bret4207 at 18:05:18 08/13/12. [Reply]  [No Email]
Leroy 08-12-2012 17:49:00 69.88.205.38 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-12-2012 09:12:22   Are the notches wore off? I wonder if the feed wheel could be made. I think I know of someone that could make it but just guessing from the New Idea, Avery and John Deere spreaders I have had without seeing the part. [Reply]  [No Email]
john chris 08-13-2012 15:27:02 71.87.212.93 Report to Moderator	Re: ih 200 manure spreader parts in reply to Leroy, 08-12-2012 17:49:00   the part broke in three places it was weld or baze before [Reply]  [No Email]
Leroy 08-15-2012 05:07:33 69.88.205.38 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-13-2012 15:27:02   If you have all the parts a GOOD welder could repair it again. Or a person that can make gears that I know of could probably make a new one if you would send him the old one as a pattern. [Reply]  [No Email]
Bret4207 08-11-2012 16:10:09 64.19.90.196 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-10-2012 21:11:59   Good luck, I've been looking for parts for mine for close to 20 years. I keep welding and looking. [Reply]  [No Email]
Cienna 08-15-2012 08:20:32 75.88.100.204 Report to Moderator	Re: ih 200 manure spreader parts in reply to Bret4207, 08-11-2012 16:10:09   Bret-----What parts are you looking for? [Reply]  [No Email]
Bret4207 08-19-2012 06:13:49 64.19.90.196 Report to Moderator	Re: ih 200 manure spreader parts in reply to Cienna, 08-15-2012 08:20:32   Sorry I missed your post. I was looking for the apron drive sprocket. I did as I posted and put on 67H chain when the old "S" apron chain corroded away. Busted a lot of teeth on the sprocket. Now I'm changing the apron chain axle sprockets to 67s. My big concern was the apron drive sprocket where I busted off a lot of the notches. But, I've got it fixed now. I found I could use a 4" angle grinder to re cut the notches. Did the same thing on my NH 329. THanks for the offer anyway. [Reply]  [No Email]
Kevin B from Illinois 08-11-2012 09:22:01 173.20.194.215 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-10-2012 21:11:59   I have the hitch and operating levers for the front it thats what you need call me 815/353/9009. [Reply]  [No Email]
john chris 08-11-2012 14:09:22 71.87.212.93 Report to Moderator	Re: ih 200 manure spreader parts in reply to Kevin B from Illinois, 08-11-2012 09:22:01   need gears [Reply]  [No Email]
Farmallboy15 08-11-2012 08:20:23 184.20.168.81 Report to Moderator	Re: ih 200 manure spreader parts in reply to john chris, 08-10-2012 21:11:59   What are you needing? Call me at 740-407-1430 [Reply]  [No Email]