Author	[Modern View]
old fashioned farmer 10-28-2012 04:32:02 99.23.122.39 Report to Moderator	Howdy folks, Looking for some ideas on what to try with my 1440. Had to install a new hydro motor down at the transmission but the combine is still not moving. When you put it in gear and move the hydro lever forward or in reverse the combine kind of shudders and then there is nothing. Any ideas would be appreciated. Thanks. --old fashioned farmer [Reply]   [No Email]
old fashioned farmer 10-30-2012 06:29:38 99.23.122.39 Report to Moderator	Re: 1440 combine won't move in reply to old fashioned farmer, 10-28-2012 04:32:02   Howdy, Just a quick update on the 1440. Dad and I were able to pull the combine into the shop (after disconnecting the shafts from the transmission to the drives). I may have blown the money on the new hydro. Apparently there is a bearing out in my transmission. Not too sure of the damage extent yet as I haven't dropped it out. Will be doing that this morning. Several ball bearings fell out when I drained the transmission yesterday evening. I was sure that the hydro was the culprit before as there was a pretty bad sound coming from it before I replaced it but now I am wondering if my ears are just bad and the sound was actually coming from the tranny. I appreciate the advice, especially on the replacing the pump and motor at the same time. New to these things so I did not know that. Hopefully can get this puppy back up and running so that when the snow from Sandy goes away we can finish our corn. God bless. --old fashioned farmer   [Reply]  [No Email]
Dalet 10-28-2012 21:23:34 184.94.141.146 Report to Moderator	Re: 1440 combine won't move in reply to old fashioned farmer, 10-28-2012 04:32:02   Replace the pump, motor, filter, fluid and bleed the air. If the drives are turning, replace the shafts too. If the shafts are stripped, you wasted lots of cash on the preceding advice. :oops:   [Reply]  [No Email]
tjiniowa 10-28-2012 16:20:37 199.120.64.97 Report to Moderator	Re: 1440 combine won't move in reply to old fashioned farmer, 10-28-2012 04:32:02   Need to change both the pump and the motor together as one unit. One will ruin the other   [Reply]  [No Email]
ohiompuller 10-28-2012 07:05:48 216.255.57.84 Report to Moderator	Re: 1440 combine won't move in reply to old fashioned farmer, 10-28-2012 04:32:02   Check the drive hub or the pump shaft. The cast hubs will take the splines out. Have someone start the combine and make sure the input shaft to the hydro pump is turning. I have replaced a lot of these pieces.   [Reply]  [No Email]
MN Scott 10-28-2012 06:34:39 184.158.81.118 Report to Moderator	Re: 1440 combine won't move in reply to old fashioned farmer, 10-28-2012 04:32:02   You replaced the hydro motor and not the pump to? When one fails it fills the other with metal shavings and pretty much ruins it to. Good practice to go thru both the pump and motor for a long lasting repair.   [Reply]  [No Email]
Erik Ks farmer 10-28-2012 05:18:23 199.241.240.16 Report to Moderator	Re: 1440 combine won't move in reply to old fashioned farmer, 10-28-2012 04:32:02   There is air in the system, if you have an operators manual there are direction in it on how to bleed the system.   [Reply]  [No Email]
old fashioned farmer 10-28-2012 06:03:59 99.23.122.39 Report to Moderator	Re: 1440 combine won't move in reply to Erik Ks farmer, 10-28-2012 05:18:23   I wondered about that. I went through the steps the manual had when you drain the system. Maybe it didn't quite get the air out. Thanks for the input. God bless. old fashioned farmer   [Reply]  [No Email]