|
| |
| Ford Tractors Discussion Forum |
Topic: Re: hydraulic valve 631
[Show Entire Topic] [Return to Forum]
| Author |
[Modern View]
|
| Larharm
11-16-2012 11:26:08
97.122.224.208
|
So a 2 valve log splitter or loader / generic should have three ports one to cycl for vertical lift and two to cycl for angle
|
|
|
| soundguy
11-16-2012 12:43:50
184.4.146.28
|
|
Re: hydraulic valve 631 in reply to Larharm, 11-16-2012 11:26:08
|
|
| a 2 spool valve is generally setup as DA and will have 4 ports. many times you can make one of the spools operate in SA mode by adjusting a sleave or set screw.. thus you only use 3 of the ports and plug the 4th one so no dirt gets in it.
|
|
|
| Larharm
11-16-2012 14:25:33
97.122.224.208
|
|
Re: hydraulic valve 631 in reply to soundguy, 11-16-2012 12:43:50
|
|
| I think I am getting the hang of it now, so i will just leave the lever on the existing valve under the seat and the two hoses that now go to the QD there and plug in male hoses from new valve. Just this set up bypass the existing lever control that is on the valve under the seat i now use it for the existing cycl to raise and lower
|
|
|
| soundguy
11-16-2012 15:36:23
173.103.119.239
|
|
Re: hydraulic valve 631 in reply to Larharm, 11-16-2012 14:25:33
|
|
| you can use the oem valve to feed another or stack a PB plate under it and run those in that loop, and still have the oe valve.. etc..
|
|
| [Show Entire Topic]
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
