Author	[Modern View]
Charley Irwin 10-05-2012 06:59:03 166.147.104.27 Report to Moderator	I have a 2000 ford three cylinder gas and the oil light keeps coming on then going off. The oil level is right on the full level and doesnt use oil between changes. Does anyone have any suggestions? This old tractor (1967 I think??) is a really great tractor...is hell for stout! Thanks for any help. Charley [Reply]   [No Email]
JMOR 10-08-2012 08:12:47 72.181.173.171 Report to Moderator	Re: Oil light coming on then going off? in reply to Cris816, 10-05-2012 06:59:03   Quoting Removed, click Modern View to seeMy earlier suggestion is still good, "It may be easier/more comforting to temporarily replace the oil pressure light switch with a mechanical pressure gauge for short period of observation. " Sean's use of Ohmmeter also a good suggestion and if you don't have an Ohmmeter, then find any old automotive light bulb (same voltage as tractor) and wire one bulb terminal to your sender switch terminal and the other bulb terminal to your battery......it should light up, then when you start engine it should go dark. [Reply]  [No Email]
Sean in PA 10-08-2012 07:24:25 71.224.102.32 Report to Moderator	Re: Oil light coming on then going off? in reply to Charley Irwin, 10-05-2012 06:59:03   With the light being intermittent before, and now after your cleaning it is on all the time, my guess would be that your cleaning job changed an intermittent short into a permanent one. The best way to check is to disconnect the wire from the oil pressure sender switch and then measure the resistance (or continuity) between the connector on the oil pressure sender switch and a good ground point with the engine running and without it running. The sender switch is on the left side of the engine block, just forward of the oil filter and just rearward of the generator (or alternator if yours has been converted). It should be close to zero ohms on an ohmmeter (or good continuity on a continuity checker) when the engine is not running, and infinite ohms (or no continuity) when the engine is running. This post was edited by Sean in PA at 07:25:11 10/08/12. [Reply]  [No Email]
Charley Irwin 10-08-2012 06:54:38 166.147.104.25 Report to Moderator	Re: Oil light coming on then going off? in reply to Charley Irwin, 10-05-2012 06:59:03   I have a update I don't understand what's going on ...I looked for a wiring problem but not being able to see all that well didn't find the culprit (yet). I did clean off the motor and washed off the degreaser and the oil light now stays on... Is this a good sign or what? Also, having had a very bad experience with "idiot" lights (lost a motor once was told to ignore it) ... My question is how can I tell 100% my motor is getting oiled properly? It's pretty out Today and so am going to spend most Of day trying to run down problem(s). Thanks everyone for your help believe me It is most appreciated...at 73 any help is appreciated☺ Charley ? [Reply]  [No Email]
RodInNS 10-08-2012 09:17:32 216.118.158.123 Report to Moderator	Re: Oil light coming on then going off? in reply to Charley Irwin, 10-08-2012 06:54:38   Don't over think this... Pull the wire off the sender. Turn the key on. If the bulb lights up you have a ground on the wire somewhere between the bulb and the end of the wire. If the light is off with the wire unhooked. Good. Rehook the wire to the sender. If while running you now have random light activity, replace the sender. If you have a consistently lit bulb at idle... then you better get a gauge on there and find out what pressure it really has. Rod [Reply]  [No Email]
Charley Irwin 10-08-2012 16:36:04 71.51.223.127 Report to Moderator	Re: Oil light coming on then going off? Problem fixed in reply to RodInNS, 10-08-2012 09:17:32   A BIG BIG THANK YOU...I finally found the problem thanks to the excellent help!! Once I found the sending unit it was right there...the clip had slipped off so I squeezed it a bit ...slipped it back on and everything was back to normal! Yes I was "over thinking the problem " and needed a bit of excellent coaching...life is good!! I will sleep good tonight! Charley [Reply]  [No Email]
Sean in PA 10-05-2012 09:26:09 71.224.102.32 Report to Moderator	Re: Oil light coming on then going off? in reply to Charley Irwin, 10-05-2012 06:59:03   "Oil Pressure Sender Switch" is the correct term. According to the New Holland parts web site: 81873524 - Switch, Pressure, Oil Sender, 3 Cylinder, Start Year: 01/01/1965 [Reply]  [No Email]
awhtx 10-05-2012 10:40:53 207.13.78.201 Report to Moderator	Re: Oil light coming on then going off? in reply to Sean in PA, 10-05-2012 09:26:09   I went to O'Reilly's Auto Parts and bought a Oil Pressure Switch for a 1965 Mustang (non-GT). It works perfectly in my 1967 5000D. It's nothing but a switch that opens at 5 or 10 PSI, extinguishing the light. [Reply]  [No Email]
RodInNS 10-05-2012 14:14:54 216.118.158.123 Report to Moderator	Re: Oil light coming on then going off? in reply to awhtx, 10-05-2012 10:40:53   The correct one, IIRC, is a 4 psi switch. You can call it whatever you like, just don't call me late for dinner. Rod [Reply]  [No Email]
awhtx 10-05-2012 14:44:46 207.13.78.201 Report to Moderator	Re: Oil light coming on then going off? in reply to RodInNS, 10-05-2012 14:14:54   You can call me anything you want as long as you call me for supper! [Reply]  [No Email]
JMOR 10-05-2012 08:47:52 72.181.173.171 Report to Moderator	Re: Oil light coming on then going off? in reply to Fordfarmer, 10-05-2012 06:59:03   Quoting Removed, click Modern View to seeYou can call it a sender if you like, I was just making a point that it is a switch..... maybe "oil pressure sender switch". It isn't important . :wink: [Reply]  [No Email]
JMOR 10-05-2012 07:53:12 72.181.173.171 Report to Moderator	Re: Oil light coming on then going off? in reply to Sean in PA, 10-05-2012 06:59:03   Quoting Removed, click Modern View to seeTMo, your tractor must not be a 2000 then, since removing the wire from the oil pressure switch ('sender' you called it) will result in light never coming on, since that is where light gets its ground. I guess it could fall off & touch the engine for ground & light up. It may be easier/more comforting to temporarily replace the oil pressure light switch with a mechanical pressure gauge for short period of observation. If all is well then, tackle the switch, wiring, light problem. If not tackle the loss of oil pressure problem before engine destructs. That would & has been my approach. [Reply]  [No Email]
TMo 10-05-2012 08:32:19 98.191.197.172 Report to Moderator	Re: Oil light coming on then going off? in reply to JMOR, 10-05-2012 07:53:12   I have a 1969 Ford 3000 gasser. I think my problem was that the connector on the wire was bouncing around and hitting the engine block. Sorry if "sender" isn't the correct terminology. Thanks, Tyler [Reply]  [No Email]
RodInNS 10-05-2012 07:50:24 216.118.158.123 Report to Moderator	Re: Oil light coming on then going off? in reply to Charley Irwin, 10-05-2012 06:59:03   If it was doing this only at idle when it's warm I'd be concerned... If it's completly random... then I'd say it's an electrical issue. The light bulb is powered continously when the key is turned on... and it receives a ground path through the sender when there's a low pressure situation... so basically a bare wire anywhere between the bulb and the sender, or a bad sender will cause the light to come on. Take a quick look at the wire from the sender to where it disappears into the harness. If you don't see anything there... pull the wire off the sender and tape the end... then see if the problem continues. If it does, pull the instrument cluster back and look at the wiring on top of the tank. That's a place where it sometimes chafes through... If the problem goes away with the sender unhooked... I'd probably just replace the sender and see what happens. Rod [Reply]  [No Email]
TMo 10-05-2012 07:24:38 98.191.197.172 Report to Moderator	Re: Oil light coming on then going off? in reply to Charley Irwin, 10-05-2012 06:59:03   Might just be a a simple electrical issue. Mine was doing that the other night and it was just that the spade connector was coming loose from the oil pressure sending unit. [Reply]  [No Email]