(800) 853-2651
SHOP NOW

where to order needle bearings for the C governor

S

SDE

Well-known Member
I copied the parts list and prices that someone had posted here. I did not copy his username and so I can not order them from him. Unless he sees this. I am going to try the Auto parts store for now. But any suggestions are appreciated
Thank you
Steve.
 
I just went thru mine last year. The part number for the bearing is a 43481D. Price was $30.92. I also put a new spring in it while I had it apart. The fastest I could get it to run was about 1,500 RPM. I use this tractor to pull with and do a little rotary mowing with it. Someone on here suggested to put a "504" spring in it. I got one 369686R2. It was $8.64. It made that tractor come alive. It is now stopped at 1,950. When I mow, I only run it about 3/4 throttle. All the parts came from my local IH dealer.
 
Well, it's NOT rocket surgery.

You can look up the FIAT part numbers at the site linked below, and order them through the nearest FIAT dealer, or GOOGLE the part numbers you need and buy them (HOPEFULLY cheaper)on-line. Or, if you are really adventurous, armed with the FIAT numbers, you can go to a SKF or Timken cross-reference website and get a number that can be ordered though any REAL auto parts store.
FIAT parts catalog for the
 
I looked at a bearing website and found the bearing, BUT min. order of $50. The Ih dealer is 30 miles away and I will be gone for the weekend and had hoped to get them ordered now and have them ready when I get back. Yes, I could or should have done my own leg work . What is FIAT? I assume it is not the Automobile.
STEVE
 
Do you remember the length of the spring? Mine is 1.75 and the stock spring is listed as 1.96 long. Mine should be replaced and if I do, I am not sure which one to buy.
Thank you
SDE
 
If I see a dealer when I am around Beloit this weekend, I will stop in and check them out.
Thank you
SDE
 
Sorry but I don't. The 504 spring was a direct replacement. What you might do is go to the archives and type in Super C governor. I had several post with questions when I did mine.
 
You must log in or register to reply here.

Similar threads

G
Almost too embarassed to post again TSX 706
Replies
15
Views
1K
JMOR
J
G
Almost too embarassed to post again TSX 706
Replies
16
Views
1K
JMOR
J
S
Farmall M Class Project: How to 'cross' bearings and sea
Replies
8
Views
2K
504
5
J
2510 axle bearings/seals question
Replies
5
Views
673
JL2510
J
L
C-123 Governor Disassembly Help (Need Tips and Tricks)
2
Replies
27
Views
3K
lgr2016
L
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top