(800) 853-2651
SHOP NOW

Farmall 560 belt pulley

D

Damon K.

Member
Anyone know what side a farmall 560 belt pulley control rod is supost to come out? The same side as the pulley or on the clutch side?
I have seen both ways...what we they originally?
Thanks
 
I think either way is correct.Just depended on which direction the shifter arm was pointed.Dont be so darn picky! The correct police will STILL find fault with it,no matter HOW perfect it is.Because there is NO perfect tractor...Especially from the 'factory'.Put it together,do a good job,make it look pretty,have fun and relax.
 
Thanks DeltaRed
I know Im very picky...I just want it to be a original as possible. I dont want anything incorrect if I can help it. But yes your rite there will always be things for people to point out that is wrong.
Thanks for the help!
 
Thanks Rich,
I just bought one and its on the right sitting on the seat. I didnt get
any linkage (control levers) with it....thats why Im trying to figure
this out.
Mine is a 1959
 
On mine it looks like the control if it were on the right side would interfere with the throttle linkage and the brake lock assembly. I could take some pictures for you if you need and email them, as I do not know how to post them here.

Rich
 
(quoted from post at 15:31:40 05/19/14) I think either way is correct.Just depended on which direction the shifter arm was pointed.Dont be so darn picky! The correct police will STILL find fault with it,no matter HOW perfect it is.Because there is NO perfect tractor...Especially from the 'factory'.Put it together,do a good job,make it look pretty,have fun and relax.
Click to expand...

Parts book shows it on the left.
 
(quoted from post at 18:31:07 05/19/14) Thanks Rich,
I just bought one and its on the right sitting on the seat. I didnt get
any linkage (control levers) with it....thats why Im trying to figure
this out.
Mine is a 1959
Click to expand...

Probably from an M. You can reverse and rework the lever to the left side.

If you look on the rear cowl you will see 2 small hole which is where the rod support goes.
 
You must log in or register to reply here.

Similar threads

M
IH350U-C175 crankshaft pulley.
Replies
5
Views
178
13fx
1
Slow lane 49
350 utility belt change
Replies
6
Views
459
Slow lane 49
Slow lane 49
W
560 Valve setting
2
Replies
23
Views
928
WHFarms
W
G
j d 830 belt pulley brake clutch
Replies
4
Views
300
JIM MN
J
A
100 Balanced Head Mower
Replies
9
Views
456
Atilathehun99
A
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top