(800) 853-2651
SHOP NOW

560D wide front question

1

1949H

Member
Good Morning Everybody,

As my search for a wide front end for my 560D continues I'd like to ask if a wide front off a Farmall 350D would fit up to and support the weight of my 560D properly?

I have a friend who just took his off for a narrow front so he can play with weight more at the tractor pulls and he offered me the wide front. I'm really hoping it will fit!!
 
Unfortunately, no.

The 350 is a narrow-frame tractor, and the 560 is a wide frame, so the bolt holes for the saddle won't even come close to lining up.

What happened to the M front end?
 
BTW, Schwartz wide front ends can be purchased from anyone who is a dealer of A&I products. Most every local equipment dealer also handles A&I.

If you come up bust at the local tractor dealers, look for a "short line" equipment dealer who doesn't carry any of the major brands; one who just sells implements and crop handling equipment.
 
If its a IH wide front the spindles are lighter than a 560. If the price was right and condition good I would get it. They are worth more than a 560 one in a lot of places. Maybe you could trade.
If you want to try it on a 560 the rear support and steering arm for a 560 to make it bolt up are not to hard to find. Won't have the 6 bolt hubs on the 350 wide front though, if original.
 
D Slater, what about the front support saddle?

The frame rails on a 350 are narrower than a 560.
 
Front axle tube support casting that bolts to the bolsters is the same for a 350 and a 560. Same axle tube also if I remember correct. Rear support across to the frame rails is different because they match the different frame rail width of the two tractors. Also the H, SH, 300 and 350 steering arm bolt pattern is different from a 460, 560 and others. Steering arms are the made the same except for the bolt pattern for IH fronts with tie rods to rear.
 
The SM wide front fell thru unfortunately. The 350 wide front was free to me complete with no hubs or bearings so I was hoping I scored and it would fit but no such luck it sounds.

Thank you

The search continues....

PS-What is A&I? I am not familiar with them
 
You must log in or register to reply here.

Similar threads

L
7/9xx wide front & Weight Box
Replies
0
Views
114
Lynn Patrick
L
D
Farmall M Wide Front Swap
Replies
7
Views
754
Midway
M
S
My new to me 300 U
Replies
3
Views
305
Janicholson
Janicholson
R
770 wide front
Replies
4
Views
452
rrlund
R
C
Auction Buys
Replies
8
Views
461
caseman-d
C
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top