(800) 853-2651
SHOP NOW

NEED IHC 284 PART

B

Bob Evans

Member
I NEED THE HYD PUMP CONNECTOR FROM PUMP TO CRANK PULLEY ON A IHC 284 TRACTOR.THE DISC THAT BOLTS TO THE CRANK PULLEY HAS A SMALL SQUARE RECEIVER IN THE CENTER AND ALSO THE PIPE THAT HAS THE SQUARE MALE INSERT THAT GOES INTO THE RECEIVER. ANY ONE HAVE ONE OR KNOW WHERE I CAN LOCATE ONE. THANKS. BOB
 
Bob, 284 gas or diesel ? I looked up part on Messick' website and found what I think you want but listing only for gas ? Would think part would be same for either engine ? Appears both parts available but pricey. Maybe you already know that and are looking for used ? Let me know and will be glad to do more research.

Bill
 
Bill This part has failed 2 or 3 times since I bought the tractor new .I have welded and repaired it each time. I would like to find a good used one but may consider a new one as last resort. Our IHC dealer is small and in a very small town. He has never had a 284 and if I remember right his books doesn't even list a 284. Any thing you can find would be appreciated. I have a small 26 hp Yanmar with loader that I can use to garden with but I really like the 284 and would like to keep it working. Thanks for responding. Bob
 
Bob, First lets make sure I am looking up correct part for you.

Go to www.messicks.com; enter 284 and then search ;3 choices will comeup , choose 284 International Tractor ;click 07, Hydraulics ;click on 10-18 Hyd Pump Drive.

Then you should see coupling and drive illustration. Item 17 shaft is one item I think you need. New number, item 17.1 is 1002780C4 $443.39. Another choice for item 17.1 is 7430177R2 $137.33, for tractor w/power steering.

Item 21 is coupling 1002779C3 $206.36

So if those are items you need, pricey, but when I run into this I am at least glad they are still available.

Finding these parts used would be similar to hunting for hen's teeth ☺ If I have looked at correct parts let me know and I do have a couple contacts that I will gladly check for used.

I am puzzled that it only lists Gas engine in choice of Hyd Pump Drive.? I would guess if gas or diesel these parts would be the same ?

Bill
 
Bill I forgot to say mine is a gas. I looked up the parts diagram that you stated and the parts number is 17 for shaft and 21 for coupling. Both part # are the same-10027.I am 75 and pretty dumb when it comes to computers but I can't find the prices. Thanks again . Bob
 
Bob, No need to apologize about your age or computer skills. I am 73 and forced to use computers as I worked full time in parts until I was 72.

I think you need to go to bottom of diagram of picture of parts and use the bar to slide the picture to your left. This hopefully will show the rest of the part number and the price.

Bill

Bill
 
Bill I guess I will weld and grind till I can get a fit rather than paying 649.75 total for the parts. Sure wish I could locate some good used parts. Thanks for helping me on this. Bob
 
Bob, Can't blame you. Remember alignment is critical on this drive. Back to the parts diagram, make sure rubber bushings are good in item #13 coupling. Also note item #7 shims under mounting plate.

I did a search and item #21 coupler does show that Great Lakes Equipment 1-800-634-0084 may have one. You might call and check their price . No luck on shaft so far. If they have coupler reasonable that would be one less part to rebuild.

Good luck and would be interested in where you are from ? I am located in Springfield, OH near the INTERNATIONAL Truck Plant. Bill
 
Forgot to mention if you call Great Lakes Equip., they list that coupler as 1002779C4. Same thing just an updated part number.

Bill
 
Bill I'm located in north central Alabama just west of I 65. I have a Decatur,AL phone # and Hartselle, Al address. If you hear of a 284 being parted out or find anything please email me at [email protected]. Many thanks again for your help. Bob
 
You must log in or register to reply here.

Similar threads

T
Replacing generator on Super C with alternator
Replies
3
Views
176
used red MN
U
D
Tachometer cable, right angle part , tang
Replies
4
Views
347
Denteen
D
F
620 John Deere crankshaft tolerances
Replies
19
Views
748
Fidlstyks
F
B
2606 issues after rebuild
2
Replies
31
Views
696
bc
B
S
MF40 Industrial won’t start after 12 years
2
Replies
39
Views
1K
Dieseltech
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top