(800) 853-2651
SHOP NOW

Loader for 300 RC

B

bigboreG

Member
Would like to find a loader for my 300 RC. Narrow front end, several sets of weights on the rear wheels. Would are some of my choices as far as loaders go? I know they don't hold much hyd oil, so I would have to use a extra reservoir. It has three hyd valves so I am looking for a loader with hvd bucket. Thanks.
 
F 11 Farmhand 345 Du All, Koyker. Those will work fine on the 300. Hope you have power steering. A pto pump will have more lifting power than the engine driven pump.
 
I have a McCormick #31 with a blade on it on my 300. I only use it for plowing snow, although once I did use it to lift an Allis B rear end into a truck when the Massey 35 which does most of the loader work was down. I have loaded tires but no weights. It is not the greatest loader but it was on a parts tractor I bought.
Zach
 
I just put an IH 2000 loader on my 350 RC with the factory wide front end. The standard reservoir has sufficient capacity as long is it is clear full when the loader is on the ground. Not the fastest cycle time due to the limited flow rate of stock pump but it isn't a show-stopper. I don't have power steering but as long as you are moving it's not too bad.
 
Two-way cylinders do consume the amount of oil displaced by the rod. To calculate the amount just take the area of the rod and multiply it by the stroke; the bore of the cylinder doesn't factor in.
 
Thank you for all of the comments. Id like to find something that will come off easy as well if I don't need it for awhile.
 
I have had a number of loaders on different 300's over the years, if you would like photo's, plus/neg for diff loaders, setting up hyd's for float while still having down press, let me know
 
You must log in or register to reply here.

Similar threads

S
300 U loader valve ?
Replies
15
Views
386
Shelbygt
S
F
Tractor Stability Question
Replies
15
Views
963
FinallyFarming
F
M
1964 Ford 2000 Industrial - without PTO, without 3-point - any need for hydraulic reservoir under seat to be filled?
Replies
8
Views
382
Sean in PA
S
M
Massey 302 industrial with 300 loader will a 220 backhoe work?
Replies
1
Views
238
Mysteree11
M
N
JD 300 loader on a 2030
Replies
13
Views
664
Tx Jim
Tx Jim
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top