(800) 853-2651
SHOP NOW

Just picked up a 2000 loader for my 350

Brendon-KS

Brendon-KS

Well-known Member
Location
Goessel, KS
A while back I posted that a neighbor had a 2000 loader that he would sell and on Saturday we pulled it off the 460 it was on and I"ve got it setting on a hay rack. The bucket is going to a job shop today for major work but other than that it is in decent shape. Obviously the front mounts will need to be different for my 350. Before I get to work fabricating the brackets I figured I"d just check here to see if anyone had a pair of front brackets they would be interested in getting rid of. Based on information I received here before the brackets were the same from the H through the 350.

If you have a pair you"d be willing to sell please drop me a note at nafziger (at) mtelco (dot) net and we can work something out.

Thanks
 
I don"t remember for sure but if I remember right the same brackets will work.

All you need is spacers where the front of the loader frame bolts unto the side rails beside the engine.

This was all we had to do with a Freeman loader. I still have the spacers from the freeman.

If the IH loader mounts on the front bolster of the tractor you may have to do something. Because the front bolsters are different.

But we did have the Freeman on the 460 and the 350 without torching and welding.

Gary
 
You don't need to fabricate anything.

Just put 1" of spacers underneath the 460 bracket on each side, and you'll be good to go.
 
I was under the impression too that the frame was
the same just with a narrower spacing but that isn"t
the case. None of the holes line up between the 460
brackets and the 350 frame. There isn"t enough
material to add new holes to the brackets without
running into existing holes and I don"t want to
drill the tractor frame. The 460 brackets actually
pick up the tapped holes in the front casting, not
the through holes in the frame rails.
 
You must log in or register to reply here.

Similar threads

S
2001 IH Loader Question
Replies
6
Views
594
Stonewall68
S
B
Agco 6690 front end loader mounts/bracket
Replies
4
Views
156
Bradleyy12
B
G
Mounting WL-40 loader on a 706
Replies
4
Views
378
fastfarmall
F
T
Looking for a loader for a 1959 model 730, wide front end.
Replies
10
Views
512
Tx Jim
Tx Jim
P
350 U. Rethinking the 1 way power steering
Replies
3
Views
311
Janicholson
Janicholson
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top